BBB A-Plus

Water Inlet Valve

PartSelect Number PS2019482

This washing machine water inlet valve has two ports for water to enter. This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not stop filling with water
  • Leaking water
  • No hot or cold water
  • Will not fill with water
In Stock

  • Compare At

    $68.48

  • You Save

    $11.41

  • Your Price

    $57.07
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 2 NEXT > 16-20 of 20

 

1 of 2 people found this instruction helpful

Parts Used

    • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerCathy from Newnan GA

Water would not stop running

Right part sent very quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerClifford A from Melbourne Beach FL

Water level uncontrolled, belts squeeking

Removed face of control panel, removed cover on back of machine that allows access to water level hose. Disconnected hot and cold water supply. Pulled old water level hose off tub. Had to use screw type hose clamps to install as diameter of hose different from original. Removed hoses from water inlet valve. Easily installed new valve. Tilted machine on it's face to access belts. Took five minutes to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerMark from Rockaway NJ

Start wash no water

there is a micro switch in the lid that went bad , there is also a 2 amp glass fuse located in the left frame rail that went bad , working great now ?

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

    • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerWilliam from Baytown TX

Valves leaking through

Turned off water. Disconnected hoses. Removed screw holding bracket. Pulled out bracket with valve assy. Disconnected 4 wires and slid back hose clamp. Removed hose. Removed 2 screws holding valve to bracket. Reversed order for installation.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

    • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerJeremy from Chicago IL

Inlet valve leaking...

Briefly,..never opened or worked on a washer before. But alittle searching on the net revealed an easy repair job. Ordered the part from this website, and installed it successfully. Time from beginning of problem to repair.....3 days only cost me the part...about 43 bucks

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 2 NEXT > 16-20 of 20