Timer

PartSelect Number PS2019466

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not agitate.
  • Compare At

    $155.68
  • You Save

    $25.95
  • Your Price

    $129.73
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 19 reviews What's this?
1-15 of 19
 

16 of 17 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJonathan from Westfield NJ

No spin cycle

Popped-off the trim disc in the center of the timer knob to expose the locking clip. Then used a small screwdriver to pop it off. Then carefully removed the knob (careful, there's a spring inside). With the knob removed, you now have access to the two bolts that hold the timer in place. Removed them. Removed the screws that fasten the control panel and flipped it down and forward. Disconnected the wiring harness from the timer. Then reinstalled the new timer in the reverse order of disassembly. Viola'!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerFred from Austin TX

Timer was worm out and failed to work properly.

After unplugging the washer and removing the drain line I was able to pull the washer away from the wall. This provided access the top of the washer. On top of the washer machine I removed four philips screws which released the control panel. From the control panel I removed a lock washer from the timer stem, which permitt the knobs to be removed and exposed the two nutscrews which hold the timer in place. I removed the wiring harness plug from the timer and then the two nutscrews and the timer was free from the control panel.

This entire process was reversed for assembly of the new timer.

The washer is running like a new one now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 26 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerDaniel from Van Nuys CA

Follwimg the tug filing with water the cycle did not progress to agitate.

1.Unplug wash mashine.
2.Remove four sheat metal screws at top of control housing and seperate by pulling forward exposing timer.
3.Remove face plate with prongs holing it on pullout knob.
4.Remove clip securing pull out knob.
5.Remove pull out knob.
6. Remove spring.
7.Remove face plate with indicator line.
8.Remove two bolt with lock washers securing timer to metal housing.
9.Remove wire harness.
10.Reasemble in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customermichael from defiance OH

Washer wouldn't start agitating after it filled

Removed the knob on the timer. Removed the 4 screws on top of the machine. Removed the two screws with nut driver for the timer. Replaced the timer and the two screws that hold it. Plugged in the electrical socket to the timer. Put the face plate back into position and replaced the 4 screws, Put the control knob and plate back on and tried it. Worked great!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJan from Madison MS

Washer would not advance through the cycles properly.

First, using a phillips head screwdriver, I removed the four screws on the top of the control panel and tilted it forward to access the timer. Next, I removed the button on the face of the control knob and removed the retaining clip. Next, I unscrewed the screws holding the timer on the control panel using a nutdriver. I then pulled the wire harness off of the broken timer and discarded it. I then plugged the wire harness into the new timer, placed the new timer back in place and secured it with the two screws. I then tilted the front panel back up into place and secured it with the four screws. Finally, I replaced the knob, retaining clip, and cover. The washer works like it is brand new! Gotta love a good ol' Maytag!!!!! It was easy and I'm a girl!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerJACK from PADUCAH KY

Washer would not advance through cycles

UNPLUGED MACHINE FROM ELECTRICAL OUTLET. REMOVED 4 SCREWS FROM TOP OF
CONTROL PANEL. REMOVED CENTER DISC FROM
TIMER KNOB. REMOVED CLIP THAT HOLDS KNOB.
REMOVED KNOB, SPRING, AND FACE PLATE FROM TIMER. REMOVED 2 SMALL HEX HEAD SCREWS THAT HOLD TIMER TO CONTROL PANEL.
UNPLUGED ELECTRICAL PLUG FROM OLD TIMER.
REVERSED PROCEDURE WITH NEW TIMER.
MACHINE WORKS FINE.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customerdavid from Reserve LA

Machine start cycle doesnot finish.

I removed the 4 screws that hold the control cover to the machine. Next pulled out capacity knob,then I pulled out hot and cold water knob. On control dismatled it from parts com detailed drawing. Removed two screws that hold the control. Unplug-ed wire harness from Control.
Reverse this procedure to install control.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerVicki from Riverview FL

Would not advance thru the cycles

Removed screws that hold the plate over the buttons on the front of the washer. Removed timer box and replaced.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerKeri from Mayhill NM

The part was not the correct one , we need a fuse for the washing machine

the washer would not fill with water , and I had replaced the timer before,but as it turns out we need a fuse for the washing machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

Customereunice from prestonsburg KY

Timmer was bad contacts burned togeather turn on machine blow fuse knock breaker

removed power plug from outlet removed 2 top cover screws then removed timer knob cover then retaining clip then spring and back of timer knob, removed 2 hex head screws tilted timer panel forward unpluged old timer removed old timer and just installed in reverse order pluged power cord in and turned washing maching on good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerBilly from Wichita Falls TX

Points on timer controll was shorted out. Would not run.

Removed washing machine controll panel and removed the timer and replaced it with the one I ordered from PartSlect. Not bad for a old man to fix things himself,and save 20 to 30 dollars on the parts and 55 to 60 dollars on the labor. Glad I found your spot on the internet. I will tell others where they can order parts and save big bucks. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customerlawrence from spring hill KS

Timer would move but on action from washer

remover two screws from control panel remover timer dail remove plug on dail to removed dail remove two screws and unplug wires. but first unplug power.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerjudy from great falls MT

Timer would not advance

The part was over $50. less from partselect even with shipping. It took minutes to install and works wonderfully. My son did the repair so quickly with just a screwdriver; I could not believe he was done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMarie from Hamilton MT

Timer failed

Removed the screws on the top of the panel, disengaged the wiring plug and repluged it into the new timer, removed the knob from the panel and replace the new timer. Replaced the the knob and put the screws back in, done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRobert from Staten Island NY

Washer would not advance from cycle to cycle. It would wash but not spin.

First off I need to say from the time I discovered the problem to the time it was fixed was less then 24 hr. I ordered the part and the next morning at 9:30 am it was here. I unpluged the washer removed the four screws from the top of the face of the control panel, popped off the knob cover removed the stay clip and the knob came off. removed the two nuts with a nut driver. pulled the front of the panel and took out the timer unpluged it put the new one in the same was I remover the old one pluged it back in and it works like new. thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 19