Timer

PartSelect Number PS2019463

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not agitate.
  • Compare At

    $177.71
  • You Save

    $29.62
  • Your Price

    $148.09
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 20 reviews What's this?
1-5 of 20
 

21 of 22 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerMatthew from Columbus, OH

Wash cycle would not complete (would not drain)

PROBLEM: The washing machine would not go through the entire wash cycle. It would stop at the rinse cycle and the tub would not drain.

FIX: So easy, my wife made the repair while I was out of town. (1) Remove the two (of four) inner most Philips head screws to allow the control panel to swing down. (2) Pry off the cover on the cycle select knob with a flat head screw driver to allow removal the clip that holds the dial to the timer. (3) Pull off cycle select knob, cover, and spring, (4) Remove two bolts that hold the time to the control panel. (5) Remove two electrical connections from the timer. (5) Repeat steps in reverse order to install the new timer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerPeter from Georgetown, TX

12 year old washer stopped agitating during wash cycle.

First I removed the four screws on top of the front control panel, and removed the panel. I then pried out the decorative cap from the front of the cycle control knob, and removed the retainer clip on the knob shaft. I then removed the rest of the plastic knob assembly and spring, and removed the two screws holding the timer to the control panel. I disconnected the two cable connectors from the timer and removed the old timer. I reconnected the cables to the new timer, and reversed the above process to complete the installation.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

Customerwilliam from Las Vegas, NV

Switch just wore out after 13 years..

Removed front panel and replaced the switch, and the knobs. Marked the wire harness with a black marks a-lot, with the old timer so I could replace the new one the same way. EASY.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerKisan from North Potomac, MD

Washer would not work on all cycles, it would operate only on the gentle cycle

Replaced the timer.. wasn't sure if it was a timer problem. But, based on the ineternet search, took a chance to replace the timer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerArlen from Ord, NE

The washing machine would not agitate on the cycle most used by my wife.

After reading repair stories from others on the website, I was well prepared to remove the timer. I unplugged the machine from the electrical outlet and pryed out the center cover of the timer knobs with a pocket knife, removed the holding clip from the shaft and removed the two knobs and spring. I then removed the four screws from the top of the control panel, lifted the panel slightly upward and tipped the panel forward. With the aid of a pocket knife I then removed the two electrical connectors from the timer while depressing the plastic locking tabs. The control panel was then tipped upright and the two machine screws holding the timer were removed at the front. The timer was then free to be removed from the control panel. The new timer was installed in the reverse order of the removal. The old timer appeared to be working but had some signs of corrosion which was probably not allowing some of the electrical contacts to make a good connection. I attempted to clean the contacts but this did not help and decided this would only be a temporary fix if I did get it to work again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 20