Timer

PartSelect Number PS2019338

This timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not agitate.
  • Compare At

    $152.42
  • You Save

    $25.40
  • Your Price

    $127.02
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 18 reviews What's this?
1-15 of 18
 

13 of 14 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert from Camarillo CA

Washing machine would only fill with water. Timer would work but machine didn't cycle.

I removed front control panel using phillip head driver to remove the two screws on top of panel.Removed Timer knob by gently prying center cap off.Used needle nose plier to remove retaining clip to remove knob.Used nut driver to remove the Timer from panel. Unplug wire harness and install in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerDan from Mesquite TX

Wash cycles out of sync.

Unscrewed the front panel and then removed screws holding timer in place. Unplugged wires on old timer, plugged wiring harness into new time and reversed process. Washing machine works like new. I was very pleased with shipping and product quality!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDennis from Red Bud IL

Wash machine would not always turn on or it would only start in some cycles but not all.

Unplugged the machine,removed the four top screws with a phillips screwdriver,popped out the plug on the front of the knob with a small screwdriver,removed the clip with a needlenose pliers making sure not to lose the spring behind the knob,removed the two timer screws with a nutdriver and unplugged the wiring harness.Installation was just the reverse.Very easy installation and super fast service.I ordered the part at about 11am and it was delivered the next morning at 9:30am.I've ordered parts from this company before and the service was great then too.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerPATRICIA from PENSACOLA FL

Timer started bugging out

So Easy a Caveman could do it, remove knob cover, retaining pin, spring and knob. Undo the nuts, unplug the plugs. Replug the plugs, put the nuts back in put on the spring,knob and retaining clip. Put the pop in cover back on. Simple and runs like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerMarie from Spring TX

Power surge from hurrican ike!!!

After 9 days without electricity due to HURRICANE IKE it was a great relief to wash our clothes. Thanks to my loving husband who took care of the problem same day we received the part. DISCONNECT THE POWER
He removed the control panel, removed timer knob, removed 2 bolts holding timer removed connector. Installed new timer reverse order & then connected the power. After that it worked 100 %

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDale from Streator IL

Washer would not complete cycle or spin sometimes

Wife was in a hurry so 1st I called a repairman and told him I thought timer was bad, he called back and said he would have to make two trips and order part will take 3 to 5 days and cost $250 or buy new machine. Found part on line and changed it out myself, a lot easier than I thought, + great service and good advise from Part Select, Hope to get another 16 years from machine : )

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerTim from Jefferson LA

Timer on machine was not cycling.

Pried off the center cover on the setting knob with a screw driver, removed the "keeper" pin behind it with a screw driver, removed the knob, Spring and secondary knob behind the first knob simply pulling it off, removed two small bolts on the face of the control panel with 5/16" nut driver that was holding the "Timer" in place. Removed the front of the control panel (4 phillips screws on top)and unplugged the "Timer" and plugged in the new one. Reversed process. Very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerLAWRENCE from CAROL STREAM IL

Won't aggitate

It was so easy to do, removed front dials/knobs,removed 2 outer screws that hold the top cover in place. removed the cable harness from old timer, removed the 2 screws holding the timer in place. replaced timer,cable harness, re- assembled everything. Works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRoy from Calera AL

Bad timer

Just removed the timer knob, then the two screws that held the control cover on. Unplugged wiring harness from timer. removed the two 1/4" screws that held timer in place. Put in new timer, replaced screws. Plugged wiring harness into new timer. Put cover back in place, replaced screws. Replaced knob. Started wahing clothes again. Took about ten minutes at the most.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerElvis from Meriden CT

The washer would start then shut down. If I pulled the timer switch out, I would pull out and and held with some force everything would function properly.With a

Removed the two screws on top. pulled the panel apart. I disconnected the harness.Removed the timer. Installed the new timer.Connected the harness.Assembled the panel.Installed the screws.I was done. Works as good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerDaniel from Simpsonville SC

Timer gone bad

1. Popped clip to remove knob
2. Backed out two screws to remove timer
3. Pulled wiring connector from bad timer
4. Plugged connector into new timer
5. Fastened mounting screws to secure timer
6. Replaced clip on knob
7. Mama happy
8. Smiles all around

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerCharles from Billings MT

Washer won't work

replace the timer in about 20 minutes, the washer worked fine and the lady was completely happy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJeffrey from Fairport NY

Worn out timer

It was easy to determine it was a bad timer. When the washer stopped working during a cycle if you wiggled the timer knob it started working again. We found this web site and found the part we needed very easily, ordered the part and it was in our hand much faster than we expected.The part was simple to install. Pop the cover off the top of the machine, remove the knob,a couple screws and a plug. Done deal. Great diagrams on this site too and easy to navigate through. Thank you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEdward from Helena AL

Washer would not cycle all the way through the wash cycle, suspected timer

Simply removed the top screws on the control panel on top of washer, Maytag makes this easy. Then the timer was one simple plug to connect all the wires, really easy. The only tricky part was removing the handle/button from the front, bu this was done by just sliding a little clip back then the timer was easily removed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customerraymond from beaver PA

Machine quits running mid cycle

pop out center cap of knob,remove retaining clip,pull knob off,remove two screws holding the cover,pull off cover with timer still attached,disconnect plug on back of timer,use nut driver to remove timer from cover,using new timer, assemble in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 18