| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerKevin from Hinckley MN
Water leaking from fill hose
First I removed the front cover by removing screws
towards the bottom of the front. Then I removed the
bolt in each of the front top corners. Now you can lift the top all the way up. Next I located the filler hose that has the injector nozzle and the rubber injector valve. Next I loosened the clamps that hold these parts in place. Next I replaced the worn parts with the new parts and reassembled everything in reverse order.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set, Wrench set, Wrench(Adjustable)
CustomerChuck from Vashon Island WA
Leaking water
I removed front panel and top hold down screws. Then removed the clamp, replaced the rubber injector valve and the plastic injector nozzle. re-assembled the unit and tested - everything worked fine - no leaks.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsScrew drivers, Socket set, Wrench set
CustomerRonald from Meridian ID
Water was leaking on to the floor.
Assembled the parts, put them into the machine, moved it back into place, started it up and it is running fine. Thanks for the good service, good parts and they arrived on time.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers, Wrench set
CustomerRichard from Ridgefield CT
30 year old washer started to leak on left side
Noticed small pool of water on left side. Diagnosed it was injector tube. Ordered parts.
Removed front panel by removing two phillips screws and then pushed down to disengage spring clips.
Used nutdriver to remover two bolts holding top cover and then undid bleach dispenser hose.
Lifted top cover and removed clamps holding injector and fill. Replaced using 1 1/16" Stainless steel screw clamps.
THIS WAS THE FIRST REPAIR EVER ON THIS WASHER!! SIMPLY AMAZING PERFORMANCE. STILL SPINS AT HIGH RPM AND IS QUIET. Bought for my folks as a gift in 1979.
This is the reason I bought the last Maytag top loaders made in '05. Also had another one 24 years with only one repair.
Parts Select, thank you! Parts arrived in three days.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set, Wrench set
Customerfrank from mount laurel NJ
Water leaking out the bottom of the washer
removed the front and top of machine. access to the rubber hoses. removed hose, replaced the rubber injector valve. reversed process, no leaks.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers, Wrench set
CustomerEd from Paoli PA
Leaking washing machine
After reviewing the diagrams and instructions on your site, I unscrewed and removed the cover to the washing machine. I located the source of the leak and replaced the aged parts. I put everything back together and voila, no more leak. Thanks!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCindy from Jim Thorpe PA
Water was flowing from the side as it would fill
remove the front and opened the top, removed the old parts and added the new plus a new clamp that I purchased from the local store.
I'm a single mom, one income so doing repairs myself is very important. The parts came when promised and it cost me about $23.00 where a repair man could have charged me well over $100.00 just for the parts.
First time I used this website or ordered parts, I will definitely do it in the future.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
Customerlouise from gilmer TX
Rubber valve deteriorated
My grandson did the repair. Just pulled out the old valve, and I looked on the computer, did a search, found the diagram, ordered the part, a few days it arrived, he installed and tested in about 15 min. Totally happy and will order again when parts are needed. Many Thanks!!!!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerTerry from St.Louisville OH
Water leaking from top of machine during filling
Disconnected the the power and inline water hoses. Slid machine from wall about two feet.Removed the two phillips screws in front panel. Removed the two 7/16 hex head self tapping screws one in each side panel to the top. Raise the top section.The parts I replaced were on the top left side of the drum. Loosen the claims and remove the old parts. Really easy!
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsNutdriver, Screw drivers, Socket set, Wrench set
CustomerErnest from Bergenfield NJ
Water leak
open washer as direct from your repair page. Saw where water was coming from . replace parts , ran washer , job done. thank you for your help.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers, Socket set
CustomerJames from Ventura CA
Leaked during fill
Very helpful to have the parts diagram to see how to access the fill tube here on PartsSelect. Removed the two screws holding the front panel on and then undid the two hex head bolts so the lid could be tilted back. The previous repair stories posted here really helped in analyzing what to purchase. Only bought the rubber tube and injector nozzle. The plastic housing looked OK. Undid the hose clamp and out came the rubber tube. A little liquid soap on the outside and slid the tube into the housing, and hooked back the feed line. Ran the fill for a little bit to ensure the leak was gone. Re-installed the screws to attach the top and the front panel. For $20 in parts and shipping, solved the leak and machine is back in business. Thanks really helpful web site.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers, Socket set
CustomerJoe from Damascus OR
Washer leaked sometimes when filling
First, I read the stories posted on the partselect website which were very helpful.
Then I just repeated the procedure followed by others who had had the same problem, installed the new parts, and the machine was fixed.
Great idea to have this feature on your website.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
CustomerJanis from Georgetown TX
I had a leak that started just under the rim of the washer and then ran down the outside of the machine
Your website is wonderful. I read another womans account of how she fixed her machine and then I just followed her instructions...how cool is that!
|