http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/37271.gif
See part 47 in the diagram

SEAL FOR I

PartSelect Number PS2018943

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $4.81
  • You Save

    $.80
  • Your Price

    $4.01
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 4 reviews What's this?
1-4 of 4
 

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerPaul from Huntington Beach CA

The hot water intake valve did not function

This clothes washer is 35 years old and runs like a champ. I did notice a bit of water below the left rear and assumed that a hose was leaking. I let it go for about 6 months, until I could fit it into the "to-do" list. During that time, the hot/cold water intake valve died. I ordered the replacement hot/cold valve a month ago but noticed, upon removal of the valve, that there was significant water drip evidence around the electrical valve solenoids. The water drips caused the valve to die. Drips came from a clogged injector hose air break directly above the valve. Replaced all hoses and water level vacuum air line. Very easy process. The front drops off with two screws. The lid is off with two screws. All hoses easy to R/R. It took about 2 hours to complete. All replacement parts were perfect. My belts are fine so I'm ready for another 30 years of service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerJohn from Stayton OR

Washer was leaking water from top left back of tub

I opened the front of cabinet (2 philips screws at bottom corner with short screwdriver. Then took out 2 cap screws that hold top on with a 3/8" deep socket and ratchet. Once in, I removed the 3 hose clamps that hold the injector and hose in place and removed both pieces. I put the injector together and put it in and clamped it back in. I put the the seal on the tub end of the hose and installed it in the tub, then clamped the other end again. I ordered the seal separate but I wouldn't have had to since one was included with the injector hose. I reused my old hose clamps since they were in good shape. With that I closed up in reverse order. I could have gotten the parts cheaper from another online souce that I found later. Other than that, PartSelect worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerMark from Clinton NC

Water leak during fill cycle

Found the 35 year old Water injector hose was dry, brittle, and cracked. Found the new part online at a reasonable price, but was unsure if the seal came with it or not. At $3 it was worth the gamble to buy the seal. Turns out that it did come with it so in another 35 years, I'll be ready ;-) Simple replacement of the hose, one hose clamp and fitting the lip of the new seal into the hole in the top of the tub. Access was gained quickly by removing the front panel (2 phillips screws) then removing 2 sheet metal screws in the front top corners and swinging the hinged top upwards. Piece of cake.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerWilliam from Gladstone VA

Water leak

This new injector hose was much better than the original part which was plastic and had cracked with age and flexing the now one is rubber and should last a long time. The part, although it wasn't clear, came with the seal.

The only trick to installing it that I came across was with the hose clamp. I could not get the clamp over the hose once in place so the trick was to get the clamp in proper position on the hose and the put the hose over its barb (it will go with some careful "fenagleing"), you can't get the hose clamp to move after you put the hose on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4