2018741-1-M-Whirlpool-21352320-Drive-Belt.jpg
2018741-1-S-Whirlpool-21352320-Drive-Belt.jpg 2018741-2-S-Whirlpool-21352320-Drive-Belt.jpg 2018741-3-S-Whirlpool-21352320-Drive-Belt.jpg

Drive Belt

PartSelect Number PS2018741

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Burning smell.
  • Unusual Noise.
  • Pumps but will not spin.
  • Will not drain.
  • Shakes and moves.
  • Will not agitate.
  • Spins slowly.
  • Will not start.
  • Leaking water.
  • Compare At

    $17.62
  • You Save

    $2.94
  • Your Price

    $14.68
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 67 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerVirginia from Rockford IL

Machine was starting to make noises when spinning

My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

Customerjohn from centreville VA

Washing machine would be off balance in the spin cycle and bang around

Did watch the belt video and that was real easy but removing the springs and snubber ring was pretty difficult until i finally had someone help me by holding the tub. was hard to figure out how to how to get at the various parts. Howeve the washing machine is running real well now and I should be able to get several more years out of it. Better instructions or a video would have helped. I had a terrible sewer odor when the washing machine was running. i thought it was a problem with my sewer lines or traps until I took off the drain hose, almost lost it. terrible odor. when I replaced the drain hose and cleaned up the machine, the odor was gone. Saved a lot of money in needless plumbing costs. Good luck.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerLes from Moneta VA

Made noise on spin cycle

Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJack from Scottdale PA

Washer would not go into spin cycle.

I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groove and started turning the pulley by hand. The belt went right on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerDeborah from Baltimore MD

Made an awful sqealing noise and did not spin the water out all the way

Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set, Wrench(Adjustable)

CustomerRobert from Columbia MO

Pulley bearings siezed; pump quit

Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerPatrick from Indianola MS

Washer machine just shut down.

All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerEllie from Eastview KY

Washing machine filled with water, nothing else happened.

Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be really smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerFRANK from CHULA VISTA CA

Water not draining

changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJames from Shortsville NY

Worn drive belt

tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerRicky from Colorado Springs CO

Loud sqeaking noise, burnt rubber smell, motor siezing up

Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerGlenn from Kansasville WI

Belt was frayed and pump was leaking.

I removed the back panel and then removed the old pump. After attaching the new pump I flipped the machine and attached the new belt. I put everything back together and voila, the machine works.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerJose from Elizabeth NJ

Made noise during washing and rinse cycle

It was easy to replace the water pump

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerStephanie from Ticonderoga NY

Washing machine had difficulty in spine cycle

Unplugged everything, disconnected hoses, took belt off and put new one on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerChristopher from Biloxi MS

Washer would not drain

replaced water pump and belt ,had to shim motor mounts , working pretty good , but still needs some tweaking

Help other customers find the most helpful instructions.

Were these instructions helpful?