2018741-1-S-Whirlpool-21352320-Drive Belt
2018741-1-S-Whirlpool-21352320-Drive Belt 2018741-2-S-Whirlpool-21352320-Drive Belt 2018741-3-S-Whirlpool-21352320-Drive Belt http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/48377.gif

Drive Belt

PartSelect Number PS2018741

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Burning smell.
  • Noisy.
  • Pumps but will not spin.
  • Will not drain.
  • Spins slowly.
  • Shakes and moves.
  • Will not agitate.
  • Will Not Start.
  • Leaking.
  • Compare At

    $12.91
  • You Save

    $2.15
  • Your Price

    $10.76
In Stock
Order within the next 5 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 67 reviews What's this?
1-5 of 67
 

203 of 216 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Socket set

CustomerRanse from Layton, UT

Pump was making a grinding noise

The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

40 of 52 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerJose A from Kissimmee, FL

Motor pulley burn and belt too

I pull out the motor pulley and put the new one then put belt on. but looks like the water pump its bad and I will have to order from you. Your service its the best I ever had ordering and deliver A+++++

Help other customers find the most helpful instructions.

Were these instructions helpful?

39 of 52 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers

CustomerMatthew from Ephrata, WA

Washer out of balance most of the time

watched online video help. removed washer panels. removed washer springs. disconnected hoses. pulled tub out and placed on top to expose. snubber ring. replaced snubber ring, placed tub back into proper space. replaced old springs with new set. reconnect hoses. Washer ran perfect. Was about to spend $800.00 on new washer but only spent $43.00 in parts and a few hours labor and good as new

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 21 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerstephen from redondo beach, CA

Slipping drive belt

Tipped machine 45-degrees to reveal belt on bottom of machine. Used screwdriver to remove old belt which looked fine. Installed new belt (which arrived from PartSelect within 2-days) but it felt loose. Tried machine anyway and it works just fine. Easiest repair ever. Thanks, PartSelect!

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 15 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers

CustomerDebbie from Colchester, CT

Water intermittently leaking from bottom of washer

I could not tell where the leak was coming from. It was intermittent. Also the clothes were not getting totally dry in the spin cycle. Finally the drum stopped turning. The bearing in the waterpump was shot and the water was leaking from the waterpump. Luckily or unluckily, the bearing completely went and I then found out that the intermittent leaking was coming from the pump. I replaced the pump and the belt that was damaged when the pump bearing locked up. This has resolved the leaking issue.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 67