Water Valve - 60/40

PartSelect Number PS2018243

This water valve is for 60% hot water and 40% cold - This is done to save on energy.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not stop filling with water.
  • Leaking.
  • No hot or cold water.
  • Will not fill with water.
  • Compare At

    $69.05
  • You Save

    $11.51
  • Your Price

    $57.54
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 14 reviews What's this?
1-5 of 14
 

49 of 65 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerPeter from Manorville, NY

Water would overflow from the top of the machine

The repair was very easy. Remove a few screws, switch wiring one at a time so I put them in the correct position and replace. The hose replacement was easy at the swicth but a little more difficult at the lower end of the tub due to limited space. Overall an easy job and now it works fine!

Help other customers find the most helpful instructions.

Were these instructions helpful?

41 of 47 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerWilliam from McKinney, TX

Water dripping into the tub

Unplugged the electrical plug from outlet. Disconnected the water hoses after I turned off the water supply. Using a screwdriver, popped up the washer top. Using needlenose pliers, I removed the wired from the defective valve, and removed the hose that feeds water into the tub. From the back of the washer, I removed th screw holding the valve in place. Reaching inside the washer, I removed the defective valve. I attached the electrical wires and hose to the new inlet valve prior to installing the valve. After installing the valve in place, I inserted the screw in the the valve from the back of the machine. I then reattached the hot and cold water hoses, closed the top of the washer, turned on the water supply, and plugged the machine back into the electrical outlet. I turnd the machine on, then off, and the water was no longer dripping into the machine. Problem fixed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 19 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set, Wrench (Adjustable)

Customerdaniel from cerritos, CA

Wash cycle would not start - no water would flow

I took pictures at different steps in case I forgot how it was assembled. Unplugged the power, turned off the water hoses, unplugged the hoses, pulled the washer out, took of the access panel in the lower left hand corner, took of two tec screws that hold the water valve in place, removed the four wires that were attached to the water valve, removed the water hose attached to the water valve, reattached everything to the new water valve. The only difficulty is the access panel is a bit small

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 19 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerCarolyn from Charlestown, RI

The water would not stop filling machine.Water over flowed on the floor.

found repairs on the internet. And my husband followed the repairs and the washer works wonderful thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerDONALD from LENOIR, NC

Low cold water flow

Replace valve by prying up the lid it is much easier than the small square entrance on back side bottom

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 14