Water Valve - 60/40

PartSelect Number PS2018243

This water valve is for 60% hot water and 40% cold - This is done to save on energy.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not stop filling with water.
  • Leaking water.
  • No hot or cold water.
  • Will not fill with water.
  • Compare At

    $67.69
  • You Save

    $11.28
  • Your Price

    $56.41
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 14 reviews What's this?
1-14 of 14
 

35 of 45 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerPeter from Manorville NY

Water would overflow from the top of the machine

The repair was very easy. Remove a few screws, switch wiring one at a time so I put them in the correct position and replace. The hose replacement was easy at the swicth but a little more difficult at the lower end of the tub due to limited space. Overall an easy job and now it works fine!

Help other customers find the most helpful instructions.

Were these instructions helpful?

26 of 32 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerWilliam from McKinney TX

Water dripping into the tub

Unplugged the electrical plug from outlet. Disconnected the water hoses after I turned off the water supply. Using a screwdriver, popped up the washer top. Using needlenose pliers, I removed the wired from the defective valve, and removed the hose that feeds water into the tub. From the back of the washer, I removed th screw holding the valve in place. Reaching inside the washer, I removed the defective valve. I attached the electrical wires and hose to the new inlet valve prior to installing the valve. After installing the valve in place, I inserted the screw in the the valve from the back of the machine. I then reattached the hot and cold water hoses, closed the top of the washer, turned on the water supply, and plugged the machine back into the electrical outlet. I turnd the machine on, then off, and the water was no longer dripping into the machine. Problem fixed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 15 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set, Wrench(Adjustable)

Customerdaniel from cerritos CA

Wash cycle would not start - no water would flow

i took pictures at different steps in case i forgot how it was assembled.
unplugged the power, turned off the water hoses, unplugged the hoses, pulled the washer out, took of the access panel in the lower left hand corner, took of two tec screws that hold the water valve in place, removed the four wires that were attached to the water valve, removed the water hose attached to the water valve, reattached everything to the new water valve. The only difficulty is the access panel is a bit small

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerCarolyn from Charlestown RI

The water would not stop filling machine.Water over flowed on the floor.

found repairs on the internet. And my husband followed the repairs and the washer works wonderful thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerDONALD from LENOIR NC

Low cold water flow

REPLACE VALVE BY PRYING UP THE LID IT IS MUCH EASIER THAN THE SMALL SQUARE ENTRANCE ON BACK SIDE BOTTOM

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerRichard from Geneva OH

Water would not shut off after filling desired level

Took out the two top screws out that hold the top down on the back so you can lift the lid up. Removed the cover plate on the back. Take out the screw that holds the valve in place. Reach up through the access panel and undo the to clips that hold the hose and wiring. Lift the lid up and pull the unit up and remove hose and electrical connections and put back in reverse order. Very simple to do.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Wrench set, Wrench(Adjustable)

CustomerHAMID from CHATSWORTH CA

Water was not going to the barrel

first I thought there is a problem with with hoses.problems like filter or hoses blocked.after I opened the hoses they were fine .Water was going out with power .Then I opened the valve connected to the hoses . I checked these hoses withe help of a 12 volt battery . the valve was not opening so I came to the conclusion that this part is broke.is not easy to change this part.Small place and hard to unlock the hose inside .They could design this much easier with just using longer hose.But I think then nobody will call service dept.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerChristopher from Cincinnati OH

Cold water no fill

Always check the basics first!

Mistakenly replaced the water valve (even though it was buzzing idicating it had power and showed 110V across terminals). Assumed the water lines were working. Turned out to be a clogged cold water line (safety valve clogged). Replaced both lines for good measure, machine working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerWayne from San Antonio TX

Water dripping from flume filled basin

I used a screwdriver to release the front side of the waaher top from the clips and tilted the washer top back. I then released the hose from the water valve and took out the mounting screws at the back. Replaced the valve and hooked everything back up.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerSpencer from Dayton NV

Water would not shut off - overfilling tub - flood !

Researched "trouble shooting guide" Parts Select Website--

2 possible part failures - (1)--water fill valve inop-per Parts Select Web - 74 percent change of this unit failing.
(2)--pressure line fractured - 24 percent chance of this unit failing......

Ordered both parts from Parts Select -

Replaced water fill valve (possible solenoid failure--(although a little difficult to get at valve replacemnt was easy - total porcess took a little less than an hour).

Needless to say - problem solved with valve replacement, this machine should be "good" for at least another 5 years.

Thanks for your kind help and most important - the easy to use data...........

Spence Merrell
Dayton, Nevada

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

Customerdennis from Spartanburg SC

No hot water getting through

removed old valve bought new one put it in saved money

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerChris from CO CO

No cold water would feed into machine

We replaced the valve in the washer that feeds the hot and cold water to the wash/rinse cycles. The replacement was not simple only because you have limited space to work in as the back of the machine does not come off other than a small door in the back or by removing the top. We elected to work in the small space but were able to replace the part within a short period of time and the washer is now working again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerRebecca from Pineville NC

The hot water stopped working on the washing machine.

My husband did the repair quickly and problem solved. The only difficulty was that the water valve was in a tight spot. Overall, if you are mechanically inclined and have the right tools this is do it yourself project.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

  • Water Valve - 60/40

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerPreston from Chapel Hill NC

Connection broken

I took off the back cover and it was a fairly simple repair, it just took a little time to fit the piece properly as there is little room to move tools and hands. Great diagrams on the website to ensure properly ordering. Fast shipping.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-14 of 14