2017927-1-M-Whirlpool-21001554-Water-Level-Switch.jpg
2017927-1-S-Whirlpool-21001554-Water-Level-Switch.jpg 2017927-2-S-Whirlpool-21001554-Water-Level-Switch.jpg 2017927-3-S-Whirlpool-21001554-Water-Level-Switch.jpg

Water Level Switch

PartSelect Number PS2017927

This part is able to sense the water level in the tub. When the water reaches the desired level, this switch stops the water from flowing in the tub and then the washing program begins.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not stop filling with water.
  • Compare At

    $66.25
  • You Save

    $11.04
  • Your Price

    $55.21
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 5 reviews What's this?
1-5 of 5
 

35 of 45 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerPeter from Manorville NY

Water would overflow from the top of the machine

The repair was very easy. Remove a few screws, switch wiring one at a time so I put them in the correct position and replace. The hose replacement was easy at the swicth but a little more difficult at the lower end of the tub due to limited space. Overall an easy job and now it works fine!

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 13 people found this instruction helpful

Parts Used

  • Water Level Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerHing from Toms River NJ

Water would not stop filling

1. Unplug power cord.
2. Move washer away from the wall to get access to the back of the control panel.
3. Remove 5 screws from the back panel cover with 1/4" driver, & remove cover.
4. Pull the Water Level Switch knob out from the front control panel.
5. Use pliers to slide away the retaining clip holding the clear rubber tube to the water level switch, & separate the tube from the switch.
6. Use 1/4" driver to remove 2 screws holding the switch, & remove the switch.
7. Remove the electrical wires
8. Install new switch in reverse order.

When you are testing out the washer afterward & your spouse said still not fixed because she thought the water level is too high when the water is still running? Wait a little while longer, the water should stop. She is just not used to see it filled without a load of laundry in it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 10 people found this instruction helpful

Parts Used

  • Water Level Switch

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerDan from Lombard IL

Water overflowed from tub onto floor

The problem was not in the switch but in the plastic hose from the tub to the switch. The hose was cracked and air/water leaked which therefore didn't activate the switch. I removed the top back cover to access the switch and released the hood of the machine, like a car, using a thin scaper to depress the spring loaded retaining clips. The hose was cracked at the tub just above the retainig clip. I bought new hosing at a local hardware store and replaced the switch to omit both of them as a future problem. Sell the tube with the switch as a package deal? Damage to tube may occur from violent, out of balance, spinning tub on spin cycle.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerCarolyn from Charlestown RI

The water would not stop filling machine.Water over flowed on the floor.

found repairs on the internet. And my husband followed the repairs and the washer works wonderful thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

  • Water Level Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerAaron from Lawton OK

Washer overflowing

Once the washer was unplugged, i removed the two screws on the back pannel, disconnected the three wires, rubber water line, and two screws holding it to the control panel. Quite simply reversed the process with the replacement part i ordered, which arrived overnight, and the problem was solved.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5