2017676-1-S-Whirlpool-21001108-Motor Pulley
2017676-1-S-Whirlpool-21001108-Motor Pulley 2017676-2-S-Whirlpool-21001108-Motor Pulley 2017676-3-S-Whirlpool-21001108-Motor Pulley http://www.partselect.com/Schematics/Maytag/35874.gif

Motor Pulley

PartSelect Number PS2017676

This part may differ in appearance, but functions same as original part.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Burning smell.
  • Will not drain.
  • Will not agitate.
  • Pumps but will not spin.
  • Noisy.
  • Compare At

    $15.44
  • You Save

    $2.57
  • Your Price

    $12.87
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 17 reviews What's this?
1-5 of 17
 

49 of 54 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kevin from Berwick, ME

Worn belt & burnt motor pulley

First, I looked at the site for instructions on what was wrong, it explained in full detail what and how to remove and replace. We called a local Maytag dealer and told them the part number that the site told us to order and they told us we needed a whole new motor with the plastic motor pulley. they told us the part does not come separate, so we went back to the site and ordered a $6.00 part and paid a small s/h charge and when it came in we went back to the site to see how to put it back together and the instructions were perfectly awesome. The $6 part is what we actually needed not the $178 complete motor that the dealer told us we had to buy. Thanks for this wonderful site it saved us lots of money. this is the 3rd time we order from this site and the instructions we correct all 3 times, I would recommend this site to all who has a home with repairs! Thank you for putting a well useful site together.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 19 people found this instruction helpful

Parts Used:
  • Motor Pulley
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Nancy from Candler, AL

Plastic pulley broke

No one would sell me just the plastic pulley,they said that I had to buy the whole motor.160.00 dollars.I keep searching and found partselect.com and they had the pulley on line.I had my part in two days for about 12.00 dollars and it took about 5 min. to install.Just had to tap it lightly with small hammer to move it up the rod to fit in groves.Thank-you partsselect for being honest. BOB N.C.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 14 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: James from New Braunfels, TX

Making a lot of noise during wash and drain cycle.

The drain pump assembly was going bad. It eventually froze and burned the drive belt and motor pulley up. I replaced the drain pump by removing 3 screws. I replace the motor pulley and belt in about 5 minutes without removing any parts. Simple fix. Ran through 3 cycles and works perfectly. Thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 13 people found this instruction helpful

Parts Used:
  • Motor Pulley
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set
Customer: William from Chesapeake, VA

Overloaded & caused belt to slip ruining the motor pully causing machine to make loud rumbling sound

Hardest part was removing front panel to access the motor.
Removed front panel, Tilted washer with block under the front. Removed belt. Used pully puller to remove damaged pully. Tapped on new pully with 1/2 in socket until shoulder seated on motor shaft. Replaced belt and front panel. Runs as smooth as new now. Additional note: I removed the plastic guard over the top of the motor and held an additional socket on the top of the motor shaft to avoid internal damage to the motor while tapping the new pully on the lower shaft.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Joel from Grand Rapids, MI

Belt was not turning

The reason for the belt not turning was because of a cover in the water pump pulley which did not allow the water pump to rotate and that's why the belt and the plastic motor pulley burn out. First I removed that cover and then removed the belt, the pulley was easy simply by breaking all the little teeth with a screwdriver then the pulley can be remove by using a screwdriver as a lever. putting the pulley, simply use a plastic hammer so it does not get damage be patient. finally the belt and you are done, hopefully this will help someone.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 17