Quick Question!

Have you ever purchased from PartSelect.com before?

2017573-1-S-Whirlpool-208847-Syphon Break Elbow Kit with Clamp
2017573-1-S-Whirlpool-208847-Syphon Break Elbow Kit with Clamp 2017573-2-S-Whirlpool-208847-Syphon Break Elbow Kit with Clamp 2017573-3-S-Whirlpool-208847-Syphon Break Elbow Kit with Clamp http://www.partselect.com/Schematics/Maytag/37271.gif

Syphon Break Elbow Kit with Clamp

Compare At

$23.30

You Save

$3.88

Your Price

$19.42
Order within the next 12 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2017573
Manufacturer Part Number 208847
Manufactured by Whirlpool

For drain hose 7/8".

This part works with the following brands: Maytag.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Leaking.
  • Will not drain.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 20 reviews What's this?
16-20 of 20
 

0 of 1 people found this instruction helpful

Parts Used:
  • Syphon Break Elbow Kit with Clamp
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Wrench set
Customer: JANET from CAMPBELL, CA

I broke the syphon break elbow pulling the washing machine out from the wall

First I removed the 4 screws holding the old elbow in place. Then I removed the screw holding the cover over the upper access hole on the below the syphon break elbow. I reached up through the access hole and removed the old elbow from the inside. I slid the new elbow up through the hole, aligned it with the housing plate and then screwed the screws back in to hold it in place. I had to cut about 3" off my old drain hose, because the outside diameter of the old syphon break elbow was about 1/16" larger and had stretched the end of the hose too much to fit tightly on the new elbow. I then attached the drain hose to the new elbow and tightened the hose clamp and reinserted the hose into the drain and pushed the washer back into place. (I used the old hose clamp rather than the one included with the new elbow because it still worked fine and looked sturdier than the enclosed one.)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Michael from White Plains, NY

Broke syphon elbow while moving machine

Performed repair through access cover in rear of machine. Removed screws with a nut driver and took out broken elbow. Pulled hose down to access hole to replace gasket then put back into position. installed elbow and reinstalled screws.
( this was tricky, have a helper to start the screws or place the screw in the nut driver with a piece of cloth to hold it in place), Make sure the screws are tightend evenly so the elbow sits completely against the gasket

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Syphon Break Elbow Kit with Clamp
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: John from Hilmar, CA

Broken syphon fitting in back of the washer. Piece broke off when the washer was pulled out of position to clean out water screens.

Removed the four screws that hold the part and also loosened the screw for a cover. Moved cover to gain access to inside of machine. Removed broken piece and replaced. Tightened screws and replaced plate. No leaks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Syphon Break Elbow Kit with Clamp
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Jeff from Lexington, NC

I pulled washer from the wall too far and broke the syphon break

I removed one screw from the access panel directly below the syphon break. I removed the 4 screws that secure the elbow to the valve. I reached inside the access panel and pulled the valve towards the front of the washer far enough so I could reach in and remove the broken elbow. I inserted the new elbow and replaced all the screws. I connected the drain hose to the syphon break, connected both water lines and I was done!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Elizabeth from Augusta, ME

Rusty hose clamp broke; discovered I needed a siphon assembly

One of the drain hose clamp broke (on Halloween night). After cleaning up the flood in the house (talk about a house of horrors). I removed the front panel of the washer and also discovered a mouse living in the washer on a stockpile of cat food. I also discovered that the MAYTAG washer that I bought used from a local appliance vendor did not have the correct SIPHON assembly for the drain hose thanks to PARTS SELECT. I ordered the SIPHON CONNECTOR, SIPHON BREAK ELBOW and I needed a new lid HANDLE and I discovered the CYLINDER LIGHT BULB was out.

I could have gotten the CYLINDER LIGHT BULB at a local store much cheaper. The lid HANDLE was plastic and was way over priced - it looked like metal but it was plastic.

However, the Siphon Break Elbow Kit and Connector were easy to install. You remove the front enclosure panel by removing 4 self-tapping screws at the bottom. You remove 2 sheet metal screws that hold the top enclosure panel on (in rear) and lift that cover up about five inches (prop it open really). (Which is where I also found a mouse nest which I also removed.)

I clamped a hose to the SIPHON CONNECTOR from the inside. PUT THE RUBBER GASKET INTO THE SIPHON CONNECTOR. SEAT THE SIPHON ELBOW INTO THE SIPHON CONNECTOR. FEED THE ELBOW into a precut hole on the back panel (from the inside). Then use 4 self-tapping screws (purchased separately at the local hardware store) through the precut holes into the SIPHON CONNECTOR from the outside/back. Attach the additional hose (that goes to the drain) with the hose clamp.

It actually took me longer than an hour for the whole project because I had to clean up after the mouse. Oh! And I caught the mouse the next day with a mouse trap by the frig.

It'S like a brand new washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16-20 of 20

Model Cross Reference

This part works with the following models:

PartSelect Number: PS2017573
Manufacturer Part Number: 208847
Brand Model Number Description
MaytagA104Washer - Top Loading
MaytagA105Washer - Top Loading
MaytagA110Washer - Top Loading
MaytagA112Washer - Top Loading
MaytagA180Washer - Top Loading
MaytagA181Washer - Top Loading
MaytagA182Washer - Top Loading
MaytagA183Washer - Top Loading
MaytagA190Washer - Top Loading
MaytagA1910Washer - Top Loading
MaytagA209Washer - Top Loading
MaytagA209SWasher - Top Loading
MaytagA210Washer - Top Loading
MaytagA210SWasher - Residential
MaytagA211Washer - Top Loading
MaytagA211SWasher - Top Loading
MaytagA212Washer - Top Loading
MaytagA212SWasher - Residential
MaytagA282Washer - Top Loading
MaytagA283Washer - Top Loading
MaytagA284Washer - Top Loading
MaytagA305Washer - Top Loading
MaytagA310Washer - Top Loading
MaytagA310SWasher - Residential
MaytagA312Washer - Top Loading
MaytagA312SWasher - Residential
MaytagA382Washer - Top Loading
MaytagA390Washer - Top Loading
MaytagA3910Washer - Top Loading
MaytagA410Washer - Top Loading