2017399-1-S-Whirlpool-207166-Lid Check Switch
2017399-1-S-Whirlpool-207166-Lid Check Switch 2017399-2-S-Whirlpool-207166-Lid Check Switch 2017399-3-S-Whirlpool-207166-Lid Check Switch http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/MA70A5.gif

Lid Check Switch

PartSelect Number PS2017399

This is used to start your washer once the desired water level is reached.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Will not agitate.
  • Timer will not advance.
  • Will not drain.
  • Will not fill with water.
  • Compare At

    $22.22
  • You Save

    $3.70
  • Your Price

    $18.52
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 19 reviews What's this?
1-5 of 19
 

80 of 91 people found this instruction helpful

Parts Used

  • Lid Check Switch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench set

CustomerSuleman from Canoga Park, CA

Washer was dead and would not turn on

Well the washer died and would not turn on in the middle of a wash cycle. Absolutely dead. I disconnected it from power and opened up the front panel on which all the control switches and knobs are mounted. This is removed by unscrewing 4 screws at the top of the washer.

Checked the fuse, and found blown. Replaced the fuse, closed the panel and plugged it in. Still not working. Checked the Check switches and found the Check Switch really limp. Checked with Digital Multimeter and found no continuity at either position. Unscrewed the check switch. Removal and re inspection with DMM of the check switch confirmed it was bad. Opened up the check switch and found contacts were blown.

Installed a new check switch making sure all the connecting wires go in the right places. The wiring diagram in the washer was very helpful in doing so since u dont want these wires reversed. Adjusted the plunger which operates the check switches when the lid is opened to make sure it is not over or under operating the switches. This is done by loosening the bolt holding down the check switch assembly and slidint the whole assembly forwards or backwards till the plunger has just enough push on the switches. This is done to avoid the plunger from exerting excessive pressure on the check switch and the safety switch in lid open or lid closed position. (both switches are operated by the same plunger according to the lid position)

Closed panel cover and plugged the washer in. There u go, it was alive again!

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 35 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerDale S from Walnut Ridge, AR

The washer wouldn't start after the tub filled with water.

Unpluged the washer and removed the top cover. Removed the screws holding the switches and unplug the wires. The process was very easy and the washer worked like a new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 12 people found this instruction helpful

Parts Used

  • Lid Check Switch

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerPhil from Grand Rapids, MI

Washer would stop in mid cycle

Determined that the lid switch was not completing the circuit. I then removed the 3 wires from their posts along with the 1 screw and removed the bad switch. Then, in reverse order installed the new switch. The part was 1/3rd the cost of the part sold locally. I ordered the part at 3:15pm Monday afternoon and it arrived at 1:00pm Tuesday- the next day. UNBELEIVABLE SERVICE....!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Lid Check Switch

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJOHN from ERWIN, TN

Washer fills with water wont start

checked lid switch ,plunger stuck in the in position 1 amp fuse blown took switch apart it was full of green copper corrosion stopping plunger from moving correctly. replaced switch and fuse and wow washer works

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 13 people found this instruction helpful

Parts Used

  • Lid Check Switch

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerLisa from San Diego, CA

Because the lid check switch was broken or expired - my washer would not go on and I have a baby!

I simply took the old switch out and put in the new one. The part arrived very qickly and the website was super easy to use.
thank you so much!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 19