2017399-1-S-Whirlpool-207166-Lid Check Switch
2017399-1-S-Whirlpool-207166-Lid Check Switch 2017399-2-S-Whirlpool-207166-Lid Check Switch 2017399-3-S-Whirlpool-207166-Lid Check Switch http://www.partselect.com/Schematics/Maytag/35692.gif

Lid Check Switch

PartSelect Number PS2017399

This is used to start your washer once the desired water level is reached.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Will not agitate.
  • Timer will not advance.
  • Will not drain.
  • Will not fill with water.
  • Compare At

    $22.42
  • You Save

    $3.74
  • Your Price

    $18.68
In Stock
Order within the next 8 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 19 reviews What's this?
 

8 of 13 people found this instruction helpful

Parts Used:
  • Lid Check Switch
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Lisa from San Diego, CA

Because the lid check switch was broken or expired - my washer would not go on and I have a baby!

I simply took the old switch out and put in the new one. The part arrived very qickly and the website was super easy to use.
thank you so much!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used:
  • Lid Check Switch
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Paul from Cedar Falls, IA

Washer would fill but not continue the cycle

I looked at the common problems in the owners manual and one item was the lid was not closed or the lid switch was bad. I took off the control panel and there was a schematic inside. This showed 2 lid switches. When trying to see if one switch was closed as it should be, touching the multimeter to the contacts was enough to get the washer going. .

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Mark from Rockaway, NJ

Start wash no water

there is a micro switch in the lid that went bad , there is also a 2 amp glass fuse located in the left frame rail that went bad , working great now ?

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used:
  • Lid Check Switch
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: RAFAEL from CENTERVILLE, GA

Burned out part

Good.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Ron from The Woodlands, TX

Short in door lid switch

Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.

Help other customers find the most helpful instructions.

Were these instructions helpful?