Lid Check Switch

Well the washer died and would not turn on in the middle of a wash cycle. Absolutely dead. I disconnected it from power and opened up the front panel on which all the control switches and knobs are mounted. This is removed by unscrewing 4 screws at the top of the washer.

Checked the fuse, and found blown. Replaced the fuse, closed the panel and plugged it in. Still not working. Checked the Check switches and found the Check Switch really limp. Checked with Digital Multimeter and found no continuity at either position. Unscrewed the check switch. Removal and re inspection with DMM of the check switch confirmed it was bad. Opened up the check switch and found contacts were blown.

Installed a new check switch making sure all the connecting wires go in the right places. The wiring diagram in the washer was very helpful in doing so since u dont want these wires reversed. Adjusted the plunger which operates the check switches when the lid is opened to make sure it is not over or under operating the switches. This is done by loosening the bolt holding down the check switch assembly and slidint the whole assembly forwards or backwards till the plunger has just enough push on the switches. This is done to avoid the plunger from exerting excessive pressure on the check switch and the safety switch in lid open or lid closed position. (both switches are operated by the same plunger according to the lid position)

Closed panel cover and plugged the washer in. There u go, it was alive again!

Unpluged the washer and removed the top cover. Removed the screws holding the switches and unplug the wires. The process was very easy and the washer worked like a new one.

Determined that the lid switch was not completing the circuit. I then removed the 3 wires from their posts along with the 1 screw and removed the bad switch. Then, in reverse order installed the new switch. The part was 1/3rd the cost of the part sold locally. I ordered the part at 3:15pm Monday afternoon and it arrived at 1:00pm Tuesday- the next day. UNBELEIVABLE SERVICE....!

I simply took the old switch out and put in the new one. The part arrived very qickly and the website was super easy to use.
thank you so much!

I looked at the common problems in the owners manual and one item was the lid was not closed or the lid switch was bad. I took off the control panel and there was a schematic inside. This showed 2 lid switches. When trying to see if one switch was closed as it should be, touching the multimeter to the contacts was enough to get the washer going. .

After I replaced the timer, the washer still would not wash or spin. So my son replaced the lid check switch. It was hard to remove the screw, but he finally managed to remove it and easily replaced the switch. The washer works perfectly. We kept the timer installed (also easy to do by removing the old and replacing it with the new by just unplugging wires and I think one screw) because the old one had not worked properly for a few years when I had a similar problem which resolved, except it would only work in main cycle with soaking which was sufficient for me. This large capacity washer is in good shape and I hope will last at least another 5 - 10 years. ).

I found the electrical prints in the control panel. I found the door and check switch, and used my volt meter to determine which one was bad. It was the check switch, so I went online with PartSelect and ordered what I needed.

I had the model and serial numbers. So it was really easy to find the replacement part. It arrived in just days after I ordered. We are back in business. Thank you for your service, John Gamble, Marysville, Ohio

I called a local repair service and they wanted 95 bucks for the first 30 minuets. Any thing over that was an additional 45 bucks per half hour, plus parts. Since the washer was 19 years old I thought it would cost around 300 big ones to get it repaird. We could buy a new similar model for about 550 bucks so I said, what the heck. I'll invest the 18 bucks to see if this 80 year old can fix it. The repair instruction I read on your on line were perfect. FIXED IN ABOUT 20 MINUETS.Installed the lid switch, saved a bundle and maybe another 19 years on the washer. Thanks a bunch. Walt Apple Valley Mn

checked lid switch ,plunger stuck in the in position 1 amp fuse blown took switch apart it was full of green copper corrosion stopping plunger from moving correctly. replaced switch and fuse and wow washer works

I removed the top cover that has the controls .Then started to voltage check the circuit (diagram was inside top cover) starting from L1 (had power cord pluged in) noted power was not going through the Check switch after tapping on the switch it started to work. the switch was intermitent so replaced with a new one from your company. works good now .Greg Gran

It would seem that my unhappy washer decided to
have a multiple component breakdown. after replacing one part after another, my baby runs like new. parts arrived quickly and installed easily, it was all the diagnostic that took the most time. the forums were quite helpful.

after checking obvious reasons (plugged in, breakers,) i took off control panel cover and saw that the fuse was blown, replaced it, plugged back in and it worked. After 1st wash was done, again it didnt work and the fuse was blown. I followed the wires from the fuse and they led to the lid check switch,which had a char mark leading me to beleive it was fried. I checked for continuity with an ohm meter(after disconnecting the power of course) and got no reading after pushing in the red button on the switch.I googled maytag replacement part and Partselect came up.Easy to understand ordering, and $20(including shipping,2 days later and about a half hour install, my machine was running

Found instructions at this web site, got part in a couple days, changed Lid Check Switch in 15 minutes, washer was up and running again. Best website for fixing stuff I've seen!

Very easy, and simple. Replaced part that was sent. It was a simple process, open control panel, unplug machine. Unscrewed the old part, attached the new part and starting working right away. I am very impressed with this company and the speed they shipped the parts. Will continue to use if needed and tell everyone about this site.

Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.