Quick Question!

Have you ever purchased from PartSelect.com before?

2017343-1-S-Whirlpool-206667-Washing Machine Handle Kit
2017343-1-S-Whirlpool-206667-Washing Machine Handle Kit 2017343-2-S-Whirlpool-206667-Washing Machine Handle Kit 2017343-3-S-Whirlpool-206667-Washing Machine Handle Kit http://www.partselect.com/Schematics/Maytag/36432.gif

Washing Machine Handle Kit

Compare At

$33.13

You Save

$5.52

Your Price

PartSelect Number PS2017343
Manufacturer Part Number 206667
Manufactured by Whirlpool

Used for stacked washer lid. This part may differ in appearance or color, but will function the same as the original part.

This part works with the following brands: Maytag, Jenn-Air.

This part works with the following products: Washer Dryer Combo.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 3 reviews What's this?
1-3 of 3
 

14 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Fred from Colorado Springs, CO

Control panel on stackable washer-dryer failed

After being told by the several local appliance repairmen that the unti was too old to repair, I ordered the part from PartSelect and it arrived in 2 days. It was extremely easy to repair (two screws and four nuts). The wire harnesses simply pulled off and snapped back on. This was absolutely the easiest repair I have ever done. I appreciate being able to find te part at PartSelect and the fast delivery service.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 14 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Robert from Zachary, LA

Dryer wouldn't start - 7e code on display

Found error code list on internet. stated that the 7E code was a faulty Thermistor or a few other possibilities. also found instructions to test Thermistor and clear error code. unplugged dryer plug to reset error. removed panel to access thermistor on blower duct, started dryer and ran until 7E error reappeared. removed one wire from thermister and using a volt/ohm meter. checked the resistence through the two post of thermister.
should read between 100-50 ohm. 100ohm=room temp and 50ohm=180 degree F (approx) replaced with new Thermister and problem solved.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Elizabeth from Augusta, ME

Rusty hose clamp broke; discovered I needed a siphon assembly

One of the drain hose clamp broke (on Halloween night). After cleaning up the flood in the house (talk about a house of horrors). I removed the front panel of the washer and also discovered a mouse living in the washer on a stockpile of cat food. I also discovered that the MAYTAG washer that I bought used from a local appliance vendor did not have the correct SIPHON assembly for the drain hose thanks to PARTS SELECT. I ordered the SIPHON CONNECTOR, SIPHON BREAK ELBOW and I needed a new lid HANDLE and I discovered the CYLINDER LIGHT BULB was out.

I could have gotten the CYLINDER LIGHT BULB at a local store much cheaper. The lid HANDLE was plastic and was way over priced - it looked like metal but it was plastic.

However, the Siphon Break Elbow Kit and Connector were easy to install. You remove the front enclosure panel by removing 4 self-tapping screws at the bottom. You remove 2 sheet metal screws that hold the top enclosure panel on (in rear) and lift that cover up about five inches (prop it open really). (Which is where I also found a mouse nest which I also removed.)

I clamped a hose to the SIPHON CONNECTOR from the inside. PUT THE RUBBER GASKET INTO THE SIPHON CONNECTOR. SEAT THE SIPHON ELBOW INTO THE SIPHON CONNECTOR. FEED THE ELBOW into a precut hole on the back panel (from the inside). Then use 4 self-tapping screws (purchased separately at the local hardware store) through the precut holes into the SIPHON CONNECTOR from the outside/back. Attach the additional hose (that goes to the drain) with the hose clamp.

It actually took me longer than an hour for the whole project because I had to clean up after the mouse. Oh! And I caught the mouse the next day with a mouse trap by the frig.

It'S like a brand new washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS2017343
Manufacturer Part Number: 206667
Brand Model Number Description
MaytagESE9900Washer Dryer Combo
MaytagESG9900Washer Dryer Combo
MaytagLSE1000Washer Dryer Combo
Jenn-AirLSE2700WWasher Dryer Combo
Jenn-AirLSE2700W-8Washer Dryer Combo
Jenn-AirLSE2700W-CWasher Dryer Combo
MaytagLSE7800Washer Dryer Combo
MaytagLSE7800ACLWasher Dryer Combo
MaytagLSE7800ACWWasher Dryer Combo
MaytagLSE7800ADLWasher Dryer Combo
MaytagLSE7800ADWWasher Dryer Combo
MaytagLSE7800AELWasher Dryer Combo
MaytagLSE7800AEWWasher Dryer Combo
MaytagLSE9900Washer Dryer Combo
MaytagLSE9900ACEWasher Dryer Combo
MaytagLSE9900ACLWasher Dryer Combo
MaytagLSE9900ACWWasher Dryer Combo
MaytagLSE9900ADEWasher Dryer Combo
MaytagLSE9900ADLWasher Dryer Combo
MaytagLSE9900ADWWasher Dryer Combo
MaytagLSE9900AEEWasher Dryer Combo
MaytagLSE9900AELWasher Dryer Combo
MaytagLSE9900AEWWasher Dryer Combo
MaytagLSE9900AFLWasher Dryer Combo
MaytagLSE9900AFWWasher Dryer Combo
MaytagLSG1000Washer Dryer Combo
Jenn-AirLSG2700WWasher Dryer Combo
MaytagLSG7800Washer Dryer Combo
MaytagLSG7800AALWasher Dryer Combo
MaytagLSG7800AAWWasher Dryer Combo