2017343-1-S-Whirlpool-206667-Washing Machine Handle Kit
2017343-1-S-Whirlpool-206667-Washing Machine Handle Kit 2017343-2-S-Whirlpool-206667-Washing Machine Handle Kit 2017343-3-S-Whirlpool-206667-Washing Machine Handle Kit

Washing Machine Handle Kit

PartSelect Number PS2017343

Used for stacked washer lid. This part may differ in appearance or color, but will function the same as the original part.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $31.78
  • You Save

    $5.30
  • Your Price

    $26.48
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 3 reviews What's this?
1-3 of 3
 

10 of 14 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerFred from Colorado Springs CO

Control panel on stackable washer-dryer failed

After being told by the several local appliance repairmen that the unti was too old to repair, I ordered the part from PartSelect and it arrived in 2 days. It was extremely easy to repair (two screws and four nuts). The wire harnesses simply pulled off and snapped back on. This was absolutely the easiest repair I have ever done. I appreciate being able to find te part at PartSelect and the fast delivery service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 11 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert from Zachary LA

Dryer wouldn't start - 7e code on display

Found error code list on internet. stated that the 7E code was a faulty Thermistor or a few other possibilities. also found instructions to test Thermistor and clear error code. unplugged dryer plug to reset error. removed panel to access thermistor on blower duct, started dryer and ran until 7E error reappeared. removed one wire from thermister and using a volt/ohm meter. checked the resistence through the two post of thermister.
should read between 100-50 ohm. 100ohm=room temp and 50ohm=180 degree F (approx) replaced with new Thermister and problem solved.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerElizabeth from Augusta ME

Rusty hose clamp broke; discovered I needed a siphon assembly

One of the drain hose clamp broke (on Halloween night). After cleaning up the flood in the house (talk about a house of horrors). I removed the front panel of the washer and also discovered a mouse living in the washer on a stockpile of cat food. I also discovered that the MAYTAG washer that I bought used from a local appliance vendor did not have the correct SIPHON assembly for the drain hose thanks to PARTS SELECT. I ordered the SIPHON CONNECTOR, SIPHON BREAK ELBOW and I needed a new lid HANDLE and I discovered the CYLINDER LIGHT BULB was out.

I could have gotten the CYLINDER LIGHT BULB at a local store much cheaper. The lid HANDLE was plastic and was way over priced - it looked like metal but it was plastic.

However, the Siphon Break Elbow Kit and Connector were easy to install. You remove the front enclosure panel by removing 4 self-tapping screws at the bottom. You remove 2 sheet metal screws that hold the top enclosure panel on (in rear) and lift that cover up about five inches (prop it open really). (Which is where I also found a mouse nest which I also removed.)

I clamped a hose to the SIPHON CONNECTOR from the inside. PUT THE RUBBER GASKET INTO THE SIPHON CONNECTOR. SEAT THE SIPHON ELBOW INTO THE SIPHON CONNECTOR. FEED THE ELBOW into a precut hole on the back panel (from the inside). Then use 4 self-tapping screws (purchased separately at the local hardware store) through the precut holes into the SIPHON CONNECTOR from the outside/back. Attach the additional hose (that goes to the drain) with the hose clamp.

It actually took me longer than an hour for the whole project because I had to clean up after the mouse. Oh! And I caught the mouse the next day with a mouse trap by the frig.

It'S like a brand new washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3