Siphon Break Connector Kit

PartSelect Number PS2017342

This plastic siphon break comes with a metallic clamp and gasket. It is used with many washing machines.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $26.12
  • You Save

    $4.35
  • Your Price

    $21.77
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Syphon Break Elbow Kit with Clamp

Part Number 2017573

For drain hose 7/8".

$14.39
In Stock

Pump-to-Siphon Break Drain Hose

Part Number 2019591

$44.70
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 19 reviews What's this?
16-19 of 19
 

1 of 4 people found this instruction helpful

Parts Used

  • Siphon Break Connector Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerGeorge from Atlanta GA

Washing machine leaking

First removed 2 screws(phillips) at bottom of front cover and lifted front to remove. Then removed 2 3/8 screws from under top cover and lifted cover and slid forward to exposed Syphon Break. After running briefly on spin, it was easy to see where the leak was. Syphon break was installed in 5 minutes by removing both hoses and 4 hex screws and reinstalling. Part arrived as promised in 3 days. I was very pleased with the whole experience.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Siphon Break Connector Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerLloyd from Raleigh NC

Water was showing up in front of the machine

I took the front off the machine and ran the cycle to see when it was leaking. I found it was leaking when it was draining the water out on the inside of the machine where it was going out of the machine. I took that part out off the drain hose and ordered the part no that was stamped on the part. The part came in and I reassembled everything and it did not leak.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerElizabeth from Augusta ME

Rusty hose clamp broke; discovered I needed a siphon assembly

One of the drain hose clamp broke (on Halloween night). After cleaning up the flood in the house (talk about a house of horrors). I removed the front panel of the washer and also discovered a mouse living in the washer on a stockpile of cat food. I also discovered that the MAYTAG washer that I bought used from a local appliance vendor did not have the correct SIPHON assembly for the drain hose thanks to PARTS SELECT. I ordered the SIPHON CONNECTOR, SIPHON BREAK ELBOW and I needed a new lid HANDLE and I discovered the CYLINDER LIGHT BULB was out.

I could have gotten the CYLINDER LIGHT BULB at a local store much cheaper. The lid HANDLE was plastic and was way over priced - it looked like metal but it was plastic.

However, the Siphon Break Elbow Kit and Connector were easy to install. You remove the front enclosure panel by removing 4 self-tapping screws at the bottom. You remove 2 sheet metal screws that hold the top enclosure panel on (in rear) and lift that cover up about five inches (prop it open really). (Which is where I also found a mouse nest which I also removed.)

I clamped a hose to the SIPHON CONNECTOR from the inside. PUT THE RUBBER GASKET INTO THE SIPHON CONNECTOR. SEAT THE SIPHON ELBOW INTO THE SIPHON CONNECTOR. FEED THE ELBOW into a precut hole on the back panel (from the inside). Then use 4 self-tapping screws (purchased separately at the local hardware store) through the precut holes into the SIPHON CONNECTOR from the outside/back. Attach the additional hose (that goes to the drain) with the hose clamp.

It actually took me longer than an hour for the whole project because I had to clean up after the mouse. Oh! And I caught the mouse the next day with a mouse trap by the frig.

It'S like a brand new washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Siphon Break Connector Kit

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerMitchell from Carmel IN

Water on the floor on the right side

After reading partselect.com and a few other web sites, I thught the leak was either a hose clamp, hose, or syphon break.

1. Two screws at the bottom front are removed,
2. Bottom front moved away from the machine unitl the top clips allow it to come off.
3. Remove 2 hex head screws from the lid (look up, use a nut driver or I used a socket.
4. LIft the lid from the front (similar to lifting a car hood)
5. Syphon Break is in the top back right.
6. 4 screws in the back and a hose clamp that connects to the pump.
7. Put it all back together in reverse.

I had considered replacing the hoses while I was at it, but they all looked fine. Suggest you order the Syphone Break "Kit" because it contains clamp, and ring gasket that is between the break and the discharge elbow.

Works Great! Saved myself at least $150 in service call and parts markup.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-19 of 19