2017271-1-S-Whirlpool-206154-Water Injector Hose
2017271-1-S-Whirlpool-206154-Water Injector Hose 2017271-2-S-Whirlpool-206154-Water Injector Hose 2017271-3-S-Whirlpool-206154-Water Injector Hose http://www.partselect.com/Schematics/Maytag/37271.gif

Water Injector Hose

PartSelect Number PS2017271

Manufacturer Part Number 206154
Manufactured by Whirlpool

This water injector hose is the hose found at the top of the tub cover of some clothes washers.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Compare At

    $43.61
  • You Save

    $7.27
  • Your Price

    $36.34
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

SEAL FOR I

Part Number 2018943

$4.01
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 11 reviews What's this?
1-5 of 11
 

25 of 27 people found this instruction helpful

Parts Used:
  • Water Injector Hose
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Hal from Salisbury, MD

Injector hose rotted from age

Removed the two Phillips screws from the bottom of the front panel on the washer. I pulled the front panel, from the bottom, outward untill the two spring clips released that attach the front panel to the washer top/lid assembly. Removed the two 3/8" hex head bolts securing the washer top to the side panels, with a nut driver. These are located just inside the side panels in each upper corner. Tilted the washer top / lid assembly back in order to expose the injector hose and top of tub. With 1/4 " nut driver, I loosened and removed the hose clamp around the nozzle body and the injector hose. Installed the new hose on the nozzle body , re-tightened clamp. Inserted the grooved end of the injector hose into hole on top of tub. Ran washer fill to check for leaks. None found, reassembled washer in reverse of disassembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: John from Stayton, OR

Washer was leaking water from top left back of tub

I opened the front of cabinet (2 philips screws at bottom corner with short screwdriver. Then took out 2 cap screws that hold top on with a 3/8" deep socket and ratchet. Once in, I removed the 3 hose clamps that hold the injector and hose in place and removed both pieces. I put the injector together and put it in and clamped it back in. I put the the seal on the tub end of the hose and installed it in the tub, then clamped the other end again. I ordered the seal separate but I wouldn't have had to since one was included with the injector hose. I reused my old hose clamps since they were in good shape. With that I closed up in reverse order. I could have gotten the parts cheaper from another online souce that I found later. Other than that, PartSelect worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Paul from Huntington Beach, CA

The hot water intake valve did not function

This clothes washer is 35 years old and runs like a champ. I did notice a bit of water below the left rear and assumed that a hose was leaking. I let it go for about 6 months, until I could fit it into the "to-do" list. During that time, the hot/cold water intake valve died. I ordered the replacement hot/cold valve a month ago but noticed, upon removal of the valve, that there was significant water drip evidence around the electrical valve solenoids. The water drips caused the valve to die. Drips came from a clogged injector hose air break directly above the valve. Replaced all hoses and water level vacuum air line. Very easy process. The front drops off with two screws. The lid is off with two screws. All hoses easy to R/R. It took about 2 hours to complete. All replacement parts were perfect. My belts are fine so I'm ready for another 30 years of service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Water Injector Hose
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Michael from Wauwatosa, WI

Water leaked when the washer tub filled.

I removed two screws near the bottom of the front panel and removed the panel by pulling the bottom away from the machine. Inside, I removed two cap screws, one under each front corner of the top panel. The top panel is hinged at the rear. I lifted the top panel from the front, rotated it to the rear and leaned it against the wall behind the machine. It was not necessary to disconnect any wiring. The "U" shaped water injector hose connects to the washer water source with a hose clamp and has a grommet-like end that fits in a round hole in the top of the tub. The hose had cracked and was leaking where it connected to the tub. The new injector hose was a direct replacement and was easy to install.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Water Injector Hose
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Stacey from Philadelphia, PA

Water leaking

opened washer removed old damaged part and replaced with new part, losen brackets from hose inlet, removed hose, then fit new hose into tub groves can be very frustrating take your time and be patient, once you get it on, fit over inlet, tighten brackets make sure that seal is secure by turning on the water to fill if no leak the job is done run thru complete cycle to test. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 11