Quick Question!

Have you ever purchased from PartSelect.com before?

2017149-1-S-Whirlpool-205000-Glide and Spring Kit
2017149-1-S-Whirlpool-205000-Glide and Spring Kit 2017149-2-S-Whirlpool-205000-Glide and Spring Kit 2017149-3-S-Whirlpool-205000-Glide and Spring Kit http://www.partselect.com/Schematics/Maytag/37313.gif

Glide and Spring Kit

Compare At

$33.04

You Save

$5.51

Your Price

$27.53
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2017149
Manufacturer Part Number 205000
Manufactured by Whirlpool

This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.

This part works with the following brands: Maytag, International, Jenn-Air.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Burning smell.
  • Pumps but will not spin.
  • Will not agitate.
  • Noisy.
  • Shakes and moves.
  • Spins slowly.
  • Will not drain.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Tension Springs -Set of 2

Part Number 2016844

This is a set of 2 tension springs.

$4.63
In Stock

Grease

Part Number 11738774

$4.79
In Stock

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 5 reviews What's this?
1-5 of 5
 

58 of 63 people found this instruction helpful

Parts Used:
  • Glide and Spring Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: dominic from weirton, WV

The belts were not staying tight enough to agitate properly.

Firstly, remove ac power from washer!
After removing the front panel of the washer (two philips screws), I loosened and removed the plastic motor cover and removed three hex head screws holding the motor. Have someone help you tilt the washer so you can remove the belts by "rolling" them off of the pullies (pump pully and motor pully). What I did was use a chemical degreaser to clean the motor base metal channel where the nylon sliders reside. After doing that and letting it dry, I removed the two old
springs. I ended up reinstalling the old springs because they were not stretched and I installed a new spring (total three) on the right side of the mount. A stiff metal rod with a hook on the end will help you install the springs. Squirt some of the included silicone lubricant on both sides of the motor mount channel and exercise the lube. Reinstall the motor and plastic cover over top of motor. Clean hands and clean belts while you have them out, reinstall belts and front cover and you're finished. My wife said it never ran better!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

47 of 60 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: David from Hartford, WI

Washer stopped spinng

I replace the belts - 5 min
I tried to replace the glides...I couldn't figure out how to do that..I took out the motor and and the glide mechanism...but I could not get glide braket separate from the motor mount..so i did not do this
I replace the springs and added 1 extra sping...3 instead of 2..it worked

Help other customers find the most helpful instructions.

Were these instructions helpful?   

34 of 45 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Wrench set
Customer: EVAN from DUXBURY, MA

Burning rubber smell

The repair was easy but didn't fix the issue . The transmission was the problem washing machine would no longer agitate

Help other customers find the most helpful instructions.

Were these instructions helpful?   

23 of 32 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Robert from Marlboro, NJ

Agitator action was slow/weak; bleach tube kinked

UNPLUG THE MACHINE FIRST!
a) Remove the front panel (use a putty knife to release clips)
b) Fashion a small hook-end out of a coat hanger
c) Install an additional glide spring (2 + 1 = 3) to get extra retraction of vee-belt around drive pulley as follows.
d) Hook end of of the new spring onto rear (back) hole of moving motor mount (observe orientation of existing springs to be sure that you're hooking up spring into hole correctly).
e) Lie on your right side, hold the spring in place with your left hand (go around back of the motor with your left hand).
f) Have someone hold the flashlight as you take a coat hanger and fish for the front end of the spring under the motor glide.
g) With front - end of spring held by coat hanger hook, pull spring towards you and slip spring into front hole of stationary motor mount.
h) Lightly spray in and around glide area with Teflon non-stick dry lube (DuPont or Liquid Wrench dri-lube product line).
Machine agitates like-new now.
Bleach Tube:
a) Remove hose clamps at both ends using a screwdriver.
b) Remove and discard old tube.
c) Slip on the hose clamps and slicker-up the ends of new tube with palmolive liquid detergent and slip onto tub and bleach dispenser.
d)Tighten clamps.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Socket set
Customer: john from COTTAGE GROVE, MN

Leaking hoses and low tension on belts

opened front of washer, removed motor, replaced glides and springs, installed motor and replaced belts. Installed new hoses and vacuum breaker. Its been a week now and no leaks or other problems.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5

Model Cross Reference

This part works with the following models:

PartSelect Number: PS2017149
Manufacturer Part Number: 205000
Brand Model Number Description
MaytagA100SWasher - Top Loading
MaytagA101Washer - Top Loading
MaytagA102Washer - Top Loading
MaytagA102SWasher - Top Loading
MaytagA103Washer - Top Loading
MaytagA103SWasher - Top Loading
MaytagA104Washer - Top Loading
MaytagA105Washer - Top Loading
MaytagA106Washer - Top Loading
MaytagA106SWasher - Residential
MaytagA107Washer - Top Loading
MaytagA107SWasher - Residential
MaytagA108Washer - Top Loading
MaytagA108SWasher - Residential
MaytagA110Washer - Top Loading
MaytagA112Washer - Top Loading
MaytagA15CAWasher
MaytagA15CMWasher
MaytagA15CTWasher
MaytagA16CAWasher
MaytagA16CMWasher
MaytagA16CTWasher
MaytagA17CAWasher
MaytagA17CMWasher
MaytagA17CTWasher
MaytagA180Washer - Top Loading
MaytagA181Washer - Top Loading
MaytagA182Washer - Top Loading
MaytagA183Washer - Top Loading
MaytagA18CAWasher