Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2017036
This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
1: Disconnected all water and electrical connections.2: Removed front panel.3: Disconnected all wires leading from the control panel and removed the top of the washer.4: Removed the springs that holds the drum down on the damper pads.5: Flipped washer upside-down so the drum would hang from the bottom of the wash. This made it easy to clean the area since it was full of dirt and ground metal dust.6: Glued new pads (per the instructions) to the cone that protrudes up from the bottom of the washer and allowed to dry.7: Lubricated the pads with the provided grease and added additional silicon grease to insure smooth operation.8: Replaced drive belt.9: Flipped the washer back up-right and installed the drum springs.10: Reconnected all wires and attached the top of the washer.11: Reconnected all electrical and water lines and tested operation.12: Replaced the front panel.Washer now runs as quite and smooth as it did when it was new.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Damper kit and Springs corrected the problem. Follow the instrutions listed on this web site and all went well..The only problem was with the damper kit. The "kit" did not include the glue needed to replace the damper pads. This cost a delay on a day and trip to a local parts store that I did not want to make. So be sure to order glue for the damper pads.
After removing the two screws that hold the front panel in place , I could easily see the areas I needed to work in .Also , I removed the two screws securing the top panel and raised it a few inches . I saw how the damper pads were worn away . I removed the 3 dampering springs by removing the eyebolts and the base mounting nuts . After the dampering springs are removed , the washing drum can be lifted up off the bottom .Just lean the machine towards the rear and place a 4x4 lumber under the big pulley on the bottom and allow the machine to slowly come forward again resting on the lumber .I followed the instructions supplied and cleaned the excess dirt and debris away from the pad mounting areas . I applied the glue as instructed and allowed it to dry . A little dexterity was needed but the new pads easily went into position . After allowing a little more glue time ,I removed the 4x4 lumber from the bottom and lowered the machine .I installed new centering springs and tightened the eyebolts to thier original positions .I secured the top and the front panels and performed a couple test cycles . perfect , no vibration at all. like new . I replaced the two drive belts on the bottom because they had never been replaced and they definitely showed wear . Another test and I was completed in around 2 hours .
The instructions that came with the damper pads were pretty clear. I moved the washer to the garage so I had room to work and lay it over on it's back when I needed to. Of course, some water came out of the washer so have some towels.There was a bit of a problem with unscrewing the nuts on the eyebolts. I expected a nut and a backing nut, but in fact the "backing" nut is attached. Took me a little while to figure that out. The hint about the electrical tape was useful to be able to screw the nut back to the original position.The only real problem was in putting the adhesive on the metal. It was too messy and hard to see, so I put the adhesive on the pad and when the glue was tacky, I placed the pad carefully on the metal. Getting the back pad properly placed required a mirror inside the cabinet. I let things dry for 2 hours before I put on the silicon grease.Make sure all the electrical connections are in place before screwing the top back on. The hot water electrical connection came off during the work and I did not notice it until i was checking the operation of the washer...had to take the top off again and use long handled needle nose pliers to put it back on.The washer works fine now....no squeaks. The job is a little bit of a hassle, but just follow the instructions. It is within the capability of anyone who can turn a socket and poke a hole in the cap of the glue.
I followed the supplied directions to remove covers, unbolt tub springs, and expose the area needed to replace the damper pads. I cleaned the area with acetone and applied a rubber adhesive (not supplied). I used tire patch compound because that is what I had on-hand. I positioned the pads and after they had dried 1/2 hour, lubricated them with the supplied grease. I reassembled the washer and it is now smooth and well behaved.
Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.
The instructions were clear. Did every step. Did 2 loads so far and everything works like new.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.