2008821-1-M-Whirlpool-12920710-High-Voltage-Board.jpg
2008821-1-S-Whirlpool-12920710-High-Voltage-Board.jpg 2008821-2-S-Whirlpool-12920710-High-Voltage-Board.jpg

High Voltage Board

PartSelect Number PS2008821

This board is located on the back of the refrigerator. It controls the operation of the unit.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Water dispenser will not dispense water.
  • Will not start.
  • Ice maker will not make ice.
  • Clicking sound.
  • Compare At

    $321.17
  • You Save

    $53.53
  • Your Price

    $267.64
In Stock
Recycling Rebate Available
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 23 reviews What's this?
16-23 of 23
 

3 of 7 people found this instruction helpful

Parts Used

  • High Voltage Board

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

CustomerFrederick from Beaufort SC

The ice and water dispensor quit working early the morning, then later in the same day. The refrigerator door (led) display lights started blinking on and off along with the ice cube door flap opening and closing.

I almost ordered the Door Led Board but read where somone else had the same problem and ordered the HV control board. Pulled the refrigerator out to gain access to the back of it. Safety tip make sure you unplug it. Located the HV Control board, release the wire connectors from it, and simply replace the board. Plug it in and follow the directions which come with the new HV board on programing it. Entering the Code off the units Data plate.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • High Voltage Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRAYBURN from DANVILLE AL

Led's flashing, and ice door flapping

took back covers off until I found the electronic control box. looked up model # and searched the internet for repair parts. ordered on sunday afternoon around 4 pm. received the following tuesday around 9 am. (great delivery time). pryed the retaining clips to remove the circuit board and unplugged the 4 wiring harnesses. installed new circuit board and covers. plugged in ref. looked up the programming code for my ref. and used the accompaning directions to program the circuit board to my ref. it immediately started to cooling and working great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • High Voltage Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJon from Jonesboro GA

Water/ice dispenser lights flashing. Not cooling.

The high voltage circuit panel in the back of the unit was bad. I was going to first replace the low voltage board behind the water/ice dispenser, but a post clued me that the real problem was the high voltage board. The part came the next day and took only a few minutes to install. The board must be programmed once installed. Follow the included instructions carefully and exactly. Fixed the problem completely.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

  • High Voltage Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customereric from little rock AR

Lights on front panel flashing and ice flapper opening and closing

Easy fix. bought control board here, removed rear panel, took old board out and stuck new one in. I called repair man first and he wanted $500 to do what i did in 15 minutes with only the cost of the control board.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • High Voltage Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerOmnimetrix from Buford GA

Control lights flashing

The control lights were flashing, so I thought that the LV board was bad. Replaced it and that did not fix the problem. After reading about another persons comment on the same issue, I did some more trouble shooting and discovered the HV board, which is in back of the refrigerator. Four screws and the cover plate comes off, then remove the clear protective cover, and unplug the electrical connectors. The board is snaped in place by tabs, so there was a little manipulating to get it free, but came right out. Replaced the board, and then you have to program the controler to the refrigerator code. Follow the instructions and it is real easy. Except remember you have to have the refrigerator doors open. Could only take 20 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

Customerwayne from baytown TX

Lights blinking on display and the ice door opening and closing.

Went on line found the problem ordered the part it took about a week and 200.00 to fix the problem

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

  • High Voltage Board

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJoe from Bixby OK

All lights on the front control panel were flashing and the ice dispenser door would open and close continually.

After doing a Google search for the issue and landing on the PartSelect website, I reviewed the explanations and directions listed. When I received the part I moved the fridge from the wall, disconnected the power, used the nut driver to remove the cover plate, removed the plastic protection shield and then unplugged each wire connector. Removing the HV board gave me the most trouble since I did not want to break the retaining clips. After a few tries I figured out how to push and pull at the same time to get the board out. Reinstallation was a breeze and the wire connectors went back easily. When power was restored, no more flashing and opening/closing. Re-programming the unit was easy by following the enclosed instructions. So much easier than hassling with a repair person and paying a lot more money to perform a simple repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • High Voltage Board

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerRandy from Fulshear TX

All led on main display board were blinking, unit was not cooling at all.

Unpluged Refer, opened 8x 8 back access pannel, removed plastic cover, unpluged the 4 plugs, pulled out old board and installed new. Re atttched all plugs. Pluged in Refer and the water dispenser started pooring out water. I valved off water. Programed code fro door buttons per instructions. Opened water valve. Refer working now, Ice maker is making ice. However the door water dispencer is now not despencing water??? I have no idea why. I am not sure where the solinoid is to check.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-23 of 23