2005745-1-S-Whirlpool-12200039-Toggle Switch - With Push Nuts
2005745-1-S-Whirlpool-12200039-Toggle Switch - With Push Nuts 2005745-2-S-Whirlpool-12200039-Toggle Switch - With Push Nuts 2005745-3-S-Whirlpool-12200039-Toggle Switch - With Push Nuts http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/33137.gif

Toggle Switch - With Push Nuts

PartSelect Number PS2005745

This toggle switch is also known as a fan switch. It has three positions: low, off, and high. This switch allows you to select the speed for the fan.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 32 reviews What's this?
1-5 of 32
 

28 of 34 people found this instruction helpful

Parts Used

  • Toggle Switch - With Push Nuts

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerCharles from Navarre, FL

Fan switch fell thru mounting hole, broken mount clip

Turn off electricity to stove. Remove 2 phillips head screws to bracket that holds fan switch and lift out. Remove 2 nuts holding broken mount clip. Remove electrical connectors one at a time a remount to same place on new fan switch. Remount fan switch to bracket which includes new mount clip using 2 nuts previously removed. Reinstall mount with new fan switch and return electrical power to stove.

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 25 people found this instruction helpful

Parts Used

  • Toggle Switch - With Push Nuts

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerT from Southfield, MI

Toggle switch to operate exhaust fan and oven light inop.

First I turned off electrical power to the range by turning off the circuit breaker for the range.
Then I removed the two screws that hold the switch plate to top of front of range. Then I pushed the sw plate back toward to rear of range to disengage it from the guide pin, and lifted the switch plate and switch. Turned the switch plate over and labelled the four wires to the switch. Removed the wire which were push-on. Which allowed me to remove the switch plate completely from the range. At my bench I used my Dremell with a cutting wheel to cut off the two push nuts/washers holding the switch to the switch plate. Removed the old switch and replaced it with the new one. Pushed to the new push nuts/washers provided in the kit, and re-assempled.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 15 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerscott from seminole, FL

Grill burner repaired

Shut down the power so I would not be surprised, removed the four front screws on panel. lifted burner knob panel to expose screws holding infinite switch and wires, easy replacement.
Even the size of the clips would not let you place them on the wrong prongs. plugged in new brurner and cooking steaks once again. Disapointed in visa's additional "International charge" of $2.83 and then $3.83 to purchase these items, but overall they were great people to deal with.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

  • Toggle Switch - With Push Nuts

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerJennifer from Easton, MD

Switch burned up; sparks and short in system

Took off plate over the rocker plate with screwdriver. Removed old switch. 2 posts were burned off!!! Plugged in new switch. Replaced panel over top. Worked great. Best $40 dollars ever spent. Saved me over $1000.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsSocket set, Wrench set

CustomerWalter from Harrisville, RI

Center post on front panel broke off making use of the timer or clock impossible. Switch on top that operates the downdraft fan and stove light was broken.

Changing the complete front control module would not have been a hard job but the two screws under the left stove knob would not release and the hex wrench stipped the bolt. I was able to undo both right screws on the right knob, releasing the knob control and the right bracket that holds the center control module. Being careful I pried the two left side tabes on the left bracket allowing me to slide the control module
out. I replaced the module and reversed my steps. The top switch that controls the downdraft and oven light was simple. Remove the two screws that holds the bracket housing the switch. Remove the two hold down compression nuts by prying them up. hold broken switch next to new one and attach the four wires. Replace switch, tried to replace the two compression nuts and after a half hour figure out they are too small. Spen another half hour in assorted nut drawer until I found two small nuts and luckily was able to force thread tham on. I can't believe I saved at least $200.00 in labor doing the repair myself. (and the stove works). I'll be doing my own repairs myself from now on. (Okay, within reason)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 32