2005745-1-S-Whirlpool-12200039-Toggle Switch - With Push Nuts
2005745-1-S-Whirlpool-12200039-Toggle Switch - With Push Nuts 2005745-2-S-Whirlpool-12200039-Toggle Switch - With Push Nuts 2005745-3-S-Whirlpool-12200039-Toggle Switch - With Push Nuts http://www.partselect.com/Schematics/Maytag/33137.gif

Toggle Switch - With Push Nuts

PartSelect Number PS2005745

This toggle switch is also known as a fan switch. It has three positions: low, off, and high. This switch allows you to select the speed for the fan.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 32 reviews What's this?
 

3 of 4 people found this instruction helpful

Parts Used:
  • Toggle Switch - With Push Nuts
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: William D from Edinburg, TX

Fan/light switch worked for fan but not for light

The job was easier than I thought it would be. Turned off power at breaker first! Used phillips screwdriver to remove 2 fairly tight screws located on the vent side of the switch mounting plate. Flipped over plate and wrote down the 4 spade tip wire colors and location on switch. Removed the wires from the switch and removed the switch by prying off the locking washer with a sharpened/filed thin putty knife to get under it and then a flat blade screwdriver to finish removing it. Put the new switch in, hooked up the spade tip wires, mounted the plate back on and turned on the power. Worked great and I even impressed my Wife!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
  • Toggle Switch - With Push Nuts
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: kevin from wheaton, IL

Fan switch on top was broken off inside outer housing rendering all controls useless, worst of the fan.

Cut power!
Removed old switch.Only problem was new switch had shifted the four 'spade' connectiors on back so when I was done fan and light switch was crossed.

Everything PartSelect had on their site was perfectly correct.

REALLY appreciated the way PartsSelect handled everything, I will be back for further help on other things.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
  • Toggle Switch - With Push Nuts
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Edwin from Shalimar, FL

The old switch disintegrated

Disconnected power from the stove. First I removed the down draft vent cover on stove top, then the two screws that held the switch plate in place, then used a wood chisel to pry the switch housing retaining washers off. Removed the remains of the old switch, Installed new switch, attached wires, and reinstalled switch plate. Placed vent cover on stove top and reconnected power.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Toggle Switch - With Push Nuts
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Christopher from Wilmington, DE

Switch for fan was heat damaged and broke

Removed top plate, disconnected old switch... Had to go to hardware store to get different push washers - the ones supplied with the part were too small. connected switch... tested connections and replaced top plate.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
  • Toggle Switch - With Push Nuts
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Neil from Winchester, VA

Fan/light switch was melted due to a hot pot placed on top.

removing the vent grid on top, by lifting off, then taking out the filter screen. removed the 2 screws on the back of the switchplate, then slide it back. made a drawing of the color wires and which way the switch faces... (it matters)
I took off the the old press-nuts by just breaking them with needle nose pliers. removed the old switch, fitted the new one (paying attention to where the little prongs and big prongs were on the old switch. used the nut-driver to press on the new nuts that came with the switch, and hooked back up the wires, and put it back.

Help other customers find the most helpful instructions.

Were these instructions helpful?