Quick Question!

Have you ever purchased from PartSelect.com before?

2005284-2-S-Whirlpool-12112425-Belt Kit
2005284-2-S-Whirlpool-12112425-Belt Kit 2005284-1-S-Whirlpool-12112425-Belt Kit 2005284-3-S-Whirlpool-12112425-Belt Kit http://www.partselect.com/Schematics/Maytag/37314.gif

Belt Kit

PartSelect Number PS2005284

This kit includes both the drive belt and the pump belt which are both "V" shaped.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Burning smell.
  • Noisy.
  • Will not agitate.
  • Pumps but will not spin.
  • Will not drain.
  • Spins slowly.
  • Shakes and moves.
  • Leaking.
  • Will Not Start.

Compare At

$29.62

You Save

$4.94

Your Price

$24.68
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 47 reviews What's this?
 

14 of 22 people found this instruction helpful

Parts Used:
  • Belt Kit
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Edward from Stroudsburg, PA

Heard squealing sound when washer went into the "spin" mode. Tub did not spin

Replaced the 2 belts according to instructions received with the belts. Very easy repair

Help other customers find the most helpful instructions.

Were these instructions helpful?   

22 of 46 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set, Wrench set
Customer: James from Ventura, CA

Repairs were easy.

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

11 of 13 people found this instruction helpful

Parts Used:
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Peter from Aurora, IL

Agitator would not work

A tension sping on the motor broke, smoking the drive belt.
step1...remove front of the washer to access spring, tip washer back & prop on short 2 x 4 board. 5 minutes
step 2... remove one end of pump belt to get new bely up to drive pulley put on belt using fingers only & replaced the end of the pump belt....2 minutes

step 3...put new spring under motor & hook one end in attaching hole on motor, reach through with pliers to grasp spring to pull end to attach spot on base...1 minute

It took longer to open up the washer front & prop it up that it took to repair it. This is a siper easy repair!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 12 people found this instruction helpful

Parts Used:
  • Belt Kit
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Matthew from Wilmington, DE

Smoking washing machine.

Well, I figured out a couple of things during this process. #1 The Washer was smoking. It had happened before (a sock got suck between the basket and the tub) so I assumed that happened again. I couldn't see anything in that space this time, so I dissasbemled the washer to see if any clothing was there. Relatively easy once finding the screws to remove the front panel. #2 What I found was a sock in the pump box. I disconnected the hoses and removed it, saw nothing between the basket and tub and ran it to see if problem corrected itself. It still was smoking. That is when I checked the belts, #3 first the pump belt, replaced it, very easy, just pulled the old one off, and wheeled the new one on. It still was smoking, #4 so I replaced the drive belt, very easy and the same as the pump belt. It still was smoking so I lubed the wheels for the belts, and #5 cleaned the residual rubber around the wheel from the old, fried, dry rotted drive belt. No more smoke!!! However #6 remember to leave space between the basket and the top of the tub, as when I put the washer back together the basket didn't spin. I removed the top and ran the spin cycle, it spun fine, reconnected and it didn't spin, the tub top was touching the basket, that's when I relized the top was on too tight. I reattached and left about 1/4 in of space and all is well now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 13 people found this instruction helpful

Parts Used:
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Debbie from Georgetown, SC

The drive belt broke.

1st We pulled the washing machine from the wall and unplugged it. 2nd We tilted the maching back against the wall so that we could see all the pullies. 3rd. We removed the two screws that afix the front panel on the lower part of the washing machine and removed the panel. 4th We removed both belts and put new belts on. 5th We put all parts back in place and plugged maching back in, slide it back in place. 6th It worked like a charm and I proceeded to wash 3 loads of laundry that evening. The only tool we needed was the phillips head screw drive to take off the front panel. It took us 5 minutes to fix the machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 8 people found this instruction helpful

Parts Used:
  • Belt Kit
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: CHRISTOPHER from BOCA RATON, FL

Washing machine tub would not drain

First I removed the two screws that held the front panel in place. Then I determined that the belt for the pump had fallen off because the drive belt was worn (and inverted) and a piece was hanging off and causing the pump belt to slip off the motor. I replaced the belt for the pump (Temporarily) to allow the tub to drain.

I replaced both belts with new belts and returned the front panel. The process took 15 minutes due to the necessity of explaining the proper use of tools to a neighbor child and allowing him to assist (required for the completion of one of his Cub Scout requirements).

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 10 people found this instruction helpful

Parts Used:
  • Belt Kit
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Ronald from Birmingham, MI

Worn belts

All I had to do is tilt the machine to expose the bottom and replace the belts. It was fast, easy and the machine works fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 14 people found this instruction helpful

Parts Used:
  • Belt Kit
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: tommy from cortlandt manor, NY

Broken belts

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Steven M. from Fort Luderdale, FL

There was a burning rubber smell from the washer

I went to the Internet and saw how to pry the front panel off the washer. This gave me access to the two belts and four pulleys underneath the washer; a pair for the Drive and a pair for the Pump. There was enough slack in the original belts that they came off with minimal effort. The new belts were easy enough to install. It took a mere seconds to install the new Spacers on the Front panel of the cabinet. The most time consuming portion of the project was getting the washer turned out of its tight corner to get access to the clips on the bottom of the front panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
  • Belt Kit
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: kevin from mundelein, IL

Burning smell from washer

Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
  • Belt Kit
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Henry from KITTERY, ME

Pump and drive belt was thorn

Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
  • Belt Kit
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Ray from Cool, CA

Broken belt

Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Belt Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Jonathan from West Tisbury, MA

The pump belt broke

I tipped the washing machine (somewhat tricky since it sits under the dryer) and saw the broken belt. Went online, found the belt I needed, bought the set of two belts since I figured it would probably be a good idea to change both belts at the same time. After a few days I had the belts in hand; it took more time to jockey the machine back into place than it did to attach the belts. No tools necessary; the washer parts are on a spring. I did need a screwdriver, however, just to re-attach the washer's front panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Belt Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools:
Customer: nicholas from white plains, NY

Agitator did not move, all other functions ok

Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Charles from Chalfont, PA

Washer was not draining completely & at times a small amount of water would leak from under the washer.

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

Help other customers find the most helpful instructions.

Were these instructions helpful?