Belt Kit

PartSelect Number PS2005284

This kit includes both the drive belt and the pump belt which are both "V" shaped.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Burning smell.
  • Noisy.
  • Will not agitate.
  • Pumps but will not spin.
  • Will not drain.
  • Spins slowly.
  • Shakes and moves.
  • Leaking.
  • Will Not Start.
  • Compare At

    $31.75
  • You Save

    $5.29
  • Your Price

    $26.46
In Stock
Order within the next 1 hr and 16 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 47 reviews What's this?
1-5 of 47
 

176 of 182 people found this instruction helpful

Parts Used

  • Belt Kit
  • Belt Kit

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerCharles from Whitman, MA

Drum would not drain and there was a banging noise when the drum spun

I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

109 of 125 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerSteven from Rockford, MN

Damper pads wore-out and had metal to metal contact which caused the washer to spin out of balance.

1: Disconnected all water and electrical connections.
2: Removed front panel.
3: Disconnected all wires leading from the control panel and removed the top of the washer.
4: Removed the springs that holds the drum down on the damper pads.
5: Flipped washer upside-down so the drum would hang from the bottom of the wash. This made it easy to clean the area since it was full of dirt and ground metal dust.
6: Glued new pads (per the instructions) to the cone that protrudes up from the bottom of the washer and allowed to dry.
7: Lubricated the pads with the provided grease and added additional silicon grease to insure smooth operation.
8: Replaced drive belt.
9: Flipped the washer back up-right and installed the drum springs.
10: Reconnected all wires and attached the top of the washer.
11: Reconnected all electrical and water lines and tested operation.
12: Replaced the front panel.

Washer now runs as quite and smooth as it did when it was new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

90 of 114 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerPeter from Westbury, NY

Washer would not start

To see if the lid switch was the problem I first jumped it out and tried to start the washer. That was the problem. I removed the main controll so I could get to the lid switch. I made the mistake of removing the screws all the way out and the metal clip fell into the body of the washer, no problem since I was changing the drive beld anyway. I realized that you do not remove the screws all the way out, you just have to loosen them and then slide out the lid switch & then replace it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

68 of 92 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set, Wrench (Adjustable)

CustomerDavid from Hartford, WI

Washer stopped spinng

I replace the belts - 5 min
I tried to replace the glides...I couldn't figure out how to do that..I took out the motor and and the glide mechanism...but I could not get glide braket separate from the motor mount..so i did not do this
I replace the springs and added 1 extra sping...3 instead of 2..it worked

Help other customers find the most helpful instructions.

Were these instructions helpful?

56 of 62 people found this instruction helpful

Parts Used

  • Belt Kit
  • Belt Kit

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerWilliam from Cary, IL

Clothes would come out of the spin cycle still wet

First found out where the belts were by tipping the machine backwards and saw that the belts were intact but extremely loose. Ordered two belts (Drive and Pump) . Re-tipped the machine and in less than three minutes, had installed the new belts. I re-hooked the hoses to the back and the machine operated as if new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 47