Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2004058
This overload and relay is used for the compressor to help protect the motor from overheating.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I rolled the fridge forward and removed the cardboard backer plate. Listening to the the compressor click in failed attempts to start, I was hoping it was just a failed relay. I unplugged the fridge,took a photo of the wiring and removed each wire from the relay. Removing the relay from the compressor took some effort. (Pull hard or pry loose with a screw driver as it is a snug fit.) Shaking the failed part gave the sounds of a baby's rattle so ordered the replacement kit.The parts received were quite different that the original. Rather than a modular plug, the kit consists of the two components a wire jumper and a large plastic housing. Perhaps there will be less heat build up and this will last longer.The directions were straight forward, but the black & white photos had little contrast and some details were hard to make out. The wiring color scheme in the instructions did not match my unit. Checking the on-line wiring plans confirmed that it had also been missing a ground wire to the compressor all these years -- yikes! After plugging in the two components to the compressor and connecting the wires and adding a ground, I aligned the plastic housing over the connections. The cover did not snap into place with any authority, but appears to be secure.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Problem: My Maytag side by side door refrigerator just stopped cooling and have to discard all frozen items after I discovered being away for 3 days. First, I went to my computer and read some of the repair stories at Part Select “Need help with your repair?” and installation video guide.1. I ordered the Refrigerator Adaptive Defrost Board (ADP) - followed the procedures how to disconnect and installed the new part. Unfortunately, it did not correct the problem and only warm is coming out.2. I ordered the Defrost Heater Thermostat Assembly - removed the old and replaced with new assembly. Again, warm air coming out. Meanwhile, I kept on hearing “clicking sound every few second” not knowing where this coming from. Again, at Part Select, I read the story about it and I ordered the Run Capacitor and the Overload/Relay with Capacitor. Soon as I opened the parts and tried to match it from the part at the back of the refrigerator and to the part from the compressor, I have discovered that they are not in compatible with the original parts from my Maytag Refrigerator and cannot be installed. And so I contacted (Email) Part Select customer service (Jeanette) if I could return the unused parts and had provided me the “Return address and the Reference Number”. This time, I gave Jeanette the Maytag Model and Serial numbers and asked where I could find this on my refrigerator and make the necessary repair and came back with the diagram and located #4 to the compressor. Ordered the correct part# PS2004058.3. Upon receipt of the part above, I was puzzled, in the plastic container are four parts, included a plastic cover. I have not given up, I removed the original part encased in white plastic container pulled straight off the compressor and examined it closely. Before detaching all the wiring, I also noted before disconnecting from wire harness and read the Diagram/Instruction Sheet provided. 4. From the four new parts provided, installed the Overload Terminal, bottom part on Compressor with one terminal to the Blue wire. Connected White Jumper to the old harness. Lastly, I plugged the PTC Start Device (two terminals) above the Overload Terminal on the Compressor with the proper wiring as I previously noted and installed the electrical cover. “Plugged in the refrigerator to the power outlet”. To test the result, I left a glass of water inside the freezer and a bottle of wine into the refrigerator. The result - I checked after 2 hours, the water was frozen and a cool wine. “Little frustration included here, as I am not an electrician.” But now, I could say, I fixed it, and very proud of this accomplishment. Thank You, PartSelect and to a great Customer Support!Safety Note: Always make sure to unplugged the refrigerator (power off) prior doing the necessary repairs.Rodolfo Julao-S.San Francisco, CA
removed relay and wires on motorinstall updated parts by using suplied wiringschmatics you suplied
removed back of cover and disconectec relay kit and reconect new parts idon't use white wire jumper now refrigeator is back in working conditions
My repairman was surprised about the availability of the part in such short time. He had told me I had to wait a week for him to get the part a replace it. As it turned out I only waited one day.Thank you!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.