The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed. The overload provides added protection for the compressor motor because in addition to protecting against excessive current, it also protects against excessive temperature use.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Fridge too warm
This part works with the following products:
Refrigerator.
This part works with the following products:
Maytag, Magic Chef, Crosley, Amana.
Part# 12002782 replaces these:
AP4009659, 1194680, 12002782, 61005518
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Frig wasn't cooling or freezing
ohms-tested the overload relay and PTC component BUT failed to test the compressor. Turns out that it was the compressor was bad and a do-it-ourselfer won't be able to change out this component. Must be licensed to install freon back into the lines once they are separated. Also specialized soldering equip. and freon equipment is needed
... Read more to perform this task. And if you add too much or the wrong kind of product or don't accurately install the bullet-piercing valve you can risk damaging the unit. So, ALWAYS Oms-test the compressor while testing the capacitor and overload and relay kit!!
Read less
Bruce from CORRALES, NM
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fridge would run but not blow cold air. Compressor would cycle for 12 seconds every 5 minutes
remove back lower panel using nutdriver. Locate and remove Relay and Overload parts from side of Compressor which were located inside a small white box shaped cover unti held on by a spring clip. Attach new Relay and overload to 3 pin terminals on side of compressor. Attach 1 white & 1 orange/white wire to relay terminals. Attach supplied
... Read more white jumper wire to Overload and other end to Blue wire. Instal new cover supplied with kit replacing old box type cover.
Read less
Fred from Concord, NH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
61 of 87 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
December 26, 2017
I have the 4sp wiring and i'm looking for the correct relay/overload, mine is a small white box, 4spo4d419lf, next line 10 to3l, next line brazil, i just want to order the correct part so not to be faced with return problem,i also need a run capacitor for the same unit, thank you ! Bob
For model number ATB2135HRW serial # 15460594CV
Hi Bob,
Thank you for your question. Based on the model number you provided, the overload and relay kit you have referenced in your question to us is the correct part. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jason
January 12, 2018
Hi, i need the same part as bob there, i also have the 4sp wiring, but my overload/relay is part# 4sp04d419lf, next line 02 k03l. The refrigerator serial# is 15076186cl. Can i order that part from you?
For model number ATB2135HRQ
Hello Jason, Thank you for your inquiry. We show that part# 12002782 is the correct overload and relay kit for this model, and if you need the run capacitor as well, the part number is WP65889-4. Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
