http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/55028.gif
See part 18 in the diagram
http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/55028.gif

Suspension Springs - Kit of 6

PartSelect Number PS2004049

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Shakes and moves.
  • Noisy.
  • Compare At

    $36.08
  • You Save

    $6.01
  • Your Price

    $30.07
In Stock
Order within the next 12 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Suspension Spring Hook

Part Number 2017707

Order within the next 12 hrs and your part ships today!
$4.54
In Stock

Snubber Ring

Part Number 1792928

Order within the next 12 hrs and your part ships today!
$4.75
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.5 / 5.0, 24 reviews What's this?
1-5 of 24
 

93 of 96 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

Customerrobert from simpsonville, SC

Excessive banging, shaking and squeaking while on spin cycle

1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drain into small container, about 4 cups of water will come out.
5)Remove the 6 suspension Springs.
6)Place two large towels next to washer and tip machine onto its side slowly.
7)Remove drive belt from bottom, and slide out wash tub assembly thru top opening, be Careful not to damage large Plastic drive pulley on bottom of tub.
8)With tub upside-down, remove drive pully small plastic cover in center, remove E-Clip and remove pulley.
9)Slowly loosen snubber ring retaining bolts a few turns, DO NOT Remove, just loosen enough until snubber is free to move around.
10)Remove snubber ring by walking it around the retaining ring and install new snubber.
11) Clean machine cabinet and clean machine base where snubber touches with alcohol or Windex.
12) Reassemble in reverse order and Do Not Forget to reattach the small clear Water level sensing HOSE to the tub before closing the top.
13)Place Drive Belt onto the 2 small pulleys First, then slowly turn large pulley while walking belt onto it.
14)Reconnect machine to utilities and test run on small load to ensure no leaks and propper operation.
15)Enjoy Quiet free operation once again :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

39 of 52 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers

CustomerMatthew from Ephrata, WA

Washer out of balance most of the time

watched online video help. removed washer panels. removed washer springs. disconnected hoses. pulled tub out and placed on top to expose. snubber ring. replaced snubber ring, placed tub back into proper space. replaced old springs with new set. reconnect hoses. Washer ran perfect. Was about to spend $800.00 on new washer but only spent $43.00 in parts and a few hours labor and good as new

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 19 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerCarolyn from Charlestown, RI

The water would not stop filling machine.Water over flowed on the floor.

found repairs on the internet. And my husband followed the repairs and the washer works wonderful thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 12 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsWrench set

CustomerAdrian from West New York, NJ

Washer shakes and dances

No need to buy a brake wrench nor the expensive spring remover. Once the drum is out the washer turn it upside down and loose the screws holding the transmission about a little more than half way, to give the new snubber enough room to fit in, them tigh and assamble everything back together

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 9 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

CustomerHud from Woodruff, SC

Washing machine was bouncing on every load

Diagnosed that the snubber had failed.
Removed the belt, cam assembly and pulley assembly. Using Maytag brake removal tool #12002012 I removed the brake stator. I removed the front of the washing machine and the rear access plate. I removed the six tension springs. I moved the machine basket and shaft assembly toward the top of the machine. I removed the old snubber and replaced with a new one. I installed 6 new tension springs and reassembled.
The washing machine runs great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 24