Gas Oven Regulator and Valve Assembly Specifications
The purpose of the safety valve is to make sure that no gas is released until the igniter gets enough power to ignite the gas range. The purpose of the regulator is that it automatically cuts off the flow of gas at a certain pressure.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Gas igniter glows | but will not light | Will Not Start
Average Repair Rating: 3.5 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
burner valve assembly failed--no oven
Shut off gas valve & disconnect flex pipe at both ends. Remove adapter at stove end of flex pipe and re-use. Unplug from wall, turn range around and prop rear up off ground a few inches. Undo both gas pipes going up from burner valve assembly. Remove screws--one on tab toward front; green ground screw and one above it on right; two on lef
... Read moret side; one on panel covering wires going up from burner valve assembly. Undo both electrical plugs. Remove 2 screws at rear of bottom oven pan & take it out. Remove two screws at rear end of burner pipe and 1 at front end. Pull rear end of pipe gently away from burner valve assembly--this end just slips over brass nozzle w/small hole that points up at an angle. Take out burner valve assembly. Reverse to re-assemble. Magnetized screw-or nut driver makes job quick and easy. Be careful when replacing burner pipe that it fits over nozzle on burner valve assembly before tightening screws that hold pipe down. Use yellow tape to seal threads only at end of adapter that screws into burner valve assembly.
Read less
Michael from Los Angeles, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
13 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas leak
My Husband did the repair in less than an hour. He followed the way it was put together removed it the same way and replaced the whole unit very easily.
Linda from McHenry, IL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven would not come on at all.
First i turned off the gas and unpluged the electric to the stove. I removed the gas line and the screws that held the housing of the hood and valve assembly .Then i unplug 4 wires that operated the safety valveon the gas.Unthreaded 2 lines ,one for the oven and the other one for the boiler.I then replace the new hood and valve kit and pu
... Read moret everything back together and the oven works just fine.
Read less
Roger from Amanda, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
4 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
November 13, 2017
Is this a replacement regulator for a propane version of the above model?
For model number KGRS205TSS
Hi Gary,
Thank you for your question. Generally, all original parts are made in natural gas. So this regulator would be set for natural gas. You would have to change it over to LP while installing the part. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
JOHN
November 9, 2018
Hi, there is a burnt smell when using stove top or oven. Does regulator need to be replaced?Thanks
For model number MGR5755QDQ
Hello John, Thank you for the question. Reading up on this issue, it is suggested to check the insulation to see if it needs to be replaced. Hope this helps, good luck with this repair!
Oven wont light, igniter wont glow for oven
Igniter works for broiler, ive replaced the igniter, no change, i've replaced control panel, no change
If i have a bad gas valve, will that prevent the igniter from working?Thx
mike
For model number AGR5735QDW
Hi Michael,
Thank you for your question. The purpose of the safety valve is to make sure that no gas is released until the igniter gets enough power to ignite the gas range. The purpose of the regulator is that it automatically cuts off the flow of gas at a certain pressure. If the oven will not light and the igniter will not glow for the oven, then the issue may be with the spark module. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Ted
November 11, 2021
The oven ignitor will not glow. I replaced with a new one and noticed that the ignitor still does not glow. What else can I check?
For model number Jgr8875rds
Hello Ted, Thank you for the question. We suggest checking the wire harness the Igniter is connecting to. Make sure it is sending the igniter You can test for 3.2-3.6 volts AC. We hope this helps!
Was this helpful?
Thank you for voting!
Michelle
December 7, 2022
Maytag range JGR8875QDS - Issue is we can not use oven and stove top at same time seems like there is not enough gas. Gas supply coming into range is fine, if we start the oven only or burners only works fine. If I am using one of the burners then turn the oven on it will not work (also issue if using oven then try to use burners wont work). Any suggestions?
Hello Michelle, thank you for the great question. The problem seems to be with the Regulator and Valve Assembly and you may need to replace it, the part number is PS2003932. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
