| |
1 of 3 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsNutdriver, Pliers, Screw drivers
CustomerMark from DES MOINES IA
Door would not close properly
Couldn't believe how easy this was. The pictures you provided were perfect everything went exactly as the instructions said. I had to of saved at least $150.00. I would grade my mechanical skills at about a C+ at best and this was an easy fix.
If I need appliance parts, I now know where to go.
|
2 of 6 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerCharles from Bahama NC
Hinge on ice maker door was broken
I removed the outer cover from the door, removed the broken parts, and cleaned the area of debris. After cutting off the power, I replaced the solenoid and door, then prepalce the outer cover. The parts were delivered promptly, and the job when very well.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
Customerpatrick from lavista NE
The plastic door broke
followed the direction that came with the part. really easy. Thanks
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerWilliam from Harlan IA
The ice maker door broke
It was not that hard. I am not totally inept, but also not a mechanice or techie. I have discovered that a lot of repair jobs have a video that shows you how to do things, and seeing it done makes a task doable for me.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerJohn from Austin TX
Ice maker quit
I went to your site thinking the problem was lack of electronic/elec signal. Wrong! I then was guided to your "ice door repair kit". I only then realized(after viewing the repair video) that ice door SOLENOID failure was far more likely than elec circuitry failure.Since it was inexpensive I ordered the kit......gambling that it would fix it; and it did! On my first try I installed the close-door spring wrong but then reviewed the video and instantly saw my error and corrected it. I also got an elec nibble (shock) once because I hadn't disconnected as the video said to do. Good parts,good information, timely response! "Piece of Cake"! Cheers John Taylor
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerArdean from Othello WA
Ears broke off ice dispenser door
I WATCHED VIDEO FOR REPAIR, WHEN THE PART ARRIVED IT WAS A SNAP TO REPAIR.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerBill from WACO TX
Door flap of ice dispenser door was broken.
I watched the repair video before I even ordered the part. That helped me determine if I felt I could make the repair. The video was extraordinarily helpful. Can't say enough about it. I even took off the dispenser door to see if I thought I could do it. The part arrived quickly, in just a couple of days. I only needed the door flap but it came with the solenoid which is not uncommon on ordering parts. (I couldn't even find the part on other web sites much less a video on how to repair.) I reviewed the video again. I removed the drip tray and door facing as instructed. When removing the mechanism I did get incur a slight electrical shock. I had not unplugged the refrig. Duh.. Got the mechanism out and inserted the door flap. The solenoid strike bar had come out and I had a slight problem getting that back in but referenced the video and no problem. Put in all back in place. Had to clean out the ice bin some because water had frozen in the bottom. Put it back in, plugged in the refrig and I am back in business! Terrific! The video was the key for me. It gave me confidence with very clear instructions. Bill
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerCharles from Coatesville PA
Flapper from ice dispenser broken
Parts came 2 days after I ordered. Followed the included instructions, removed 4 screws, snapped the new flapper into place, put the screws back and voila - REPAIR COMPLETE!! One of the simplest appliance repairs I could imagine. Thanks Partselect!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers
CustomerBruce from Clarkridge AR
Clearing an ice jam resulted in a broken ice chute door
This is an easy repair and doesn't take hardly any time, once you can identify the electrical bridals to disconnect and the position of the new ice chute door interface point with the solenoid.
The supplied directions are complete but were quite a bit blurry. The more general dissasembly which is effectively 5 screws and two electrical bridals to remove/disconnect is straight forward. Pay particular attention to the mounting point of the ice door interface with the solenoid. I did it twice because I didn't align the door properly the first time:-)
Much too easy a job than to "call the guy."
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
Customerrichard from dix hills NY
The flapper for the ice dispensor was broken
i removed the front cover of the dispensor, easily put the parts in and put back together , the first tome the flpapper came off as i did not secure properly but it only took a few minutes to resecure and now working fine .
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerJeffrey from Royersford PA
Had to replace ice dispenser cover
VERY EASY AND WAS INSTALLED IN NO TIME> Many Thanks J
|
0 of 1 people found this instruction helpful
Parts Used
-
- Roll Pin
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyEasy
Time to do repair:15 - 30 mins
Tools
CustomerPat from Spring TX
The door strike was broken on my dispensor
The repair did not work. The new door strike did not embrace the solenoid.
I had the old spring, and it fit exactly. I also ordered a roll pin, but have no clue as what to do with it. Excellent directions came with the door strike, but nothing with the roll pin.
Was hoping the roll pin would connect the door strike to the solenoid, but did not see how that would work.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerWalter from Killeen TX
Ice dispenser door borken
Most importantly, watch the video.Made installation real simple. Better than paper instructions that come with kit.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Ice Dispenser Solenoid and Door Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerFred from Chesterfield VA
Our ice dispensor door was broken
Ordered the Ice Dispenser Solenoid & Door Kit and replaced the broken door and solenoid - easy with the right parts - FMS
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
Customermercer from cartersville GA
Broken ice dispenser bracket
Followed the video instructions and it worked like a charm. Fast service and correct parts.
|