| |
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKATHY from PLEASANT GAP PA
Oven would not maintain temperature
So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerRobert from Massapequa NY
Oven temperature lower then setpoint.
After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerEllen from Schenectady NY
Oven temperature not reaching setting/temp. Up and down
Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerWILLIAM J from JERSEY CITY NJ
Just unscred the 2 screw on the thermometer
Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRalph from Portsmouth NH
Oven would not come to set heat
slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:More than 2 hours
ToolsNutdriver
CustomerPeter from Montello WI
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerLeland from Orting WA
Oven would not heat consistently
I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerBen from Belen NM
Oven shutting off, getting an f1 error on ecm
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).
Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.
Included wiring adapters are not needed for this model oven.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerjeff from haskell NJ
F 3 signal on display pad every time oven warmed up
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerPeter from Westcliffe CO
Oven did not heat up in bake mode.
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerFloyd from Kenai AK
Variable oven heat and ignitor. Problems
moved stove away from the wall, Disconnected power, Removed 2 screws on the access panel and removed panel. Disconnected qwick release conections on heat sensor and ignitor, Removed oven door and burner cover to expose ignitor, removed 2 screws to remove ignitor and replaced ignitor. Removed 2 screws and removed sensor, replaced sensor. Reconnected qwick conects on sensor and ignitor. Replaced oven door, burner cover and access panel and checked out. Checks OK !
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerCarl from Franklin NJ
Error code f-1&f-3
Remove two screws back panel and remove sensor two screws inside top oven.
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerJoe from Troy AL
F2 and f5 if I remember correct.
Removed the two screws pulled the element out and unhooked the wires then used one of the included adapters to reinstall the new sensor then screwed the two screws back in to secure the sensor. Everything works fine now.
|