http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/49016.gif
See part 6 in the diagram

Dual Radiant Burner Element with Limiter

PartSelect Number PS2002937

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Element will not heat.
  • Compare At

    $124.66
  • You Save

    $20.78
  • Your Price

    $103.88
In Stock
Order within the next 1 hr and 22 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 3 reviews What's this?
1-3 of 3
 

4 of 5 people found this instruction helpful

Parts Used

  • Dual Radiant Burner Element with Limiter

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers

CustomerRichard from Weatherford TX

Element not heating

This was a countertop mounted cooktop. The hardest part of the repair was getting the cooktop out of the hole and separating the glass top from the burner box. It is highly recomended that you have two people to seperate the top from the burner box. Be sure you turn off the breaker to the cooktop first before you do any work. One time saver is once you have the top sperated from the box use 2- 10"-12" pieces of 1x2 or 2x4 to prop the top open. This will eleminate the need to disconnect the power leads (be sure the breaker is OFF). If you are not electrically inclined mark the color of the wires to the corrosponding terminals on the new element BEFORE you remove them from the old element. The element that I replaced was the dual heat element. I ended up having to change 2 of the terminal ends on the wiring harness becacuse they were too small for the new element. Carefully remove the wires from the old elenent using needle nose pliers and remove the old element by removing the 2 screws that hold the element to the hold down clips, then loosen the clip mounting screws & remove the element. Change terminals if needed & reassmble in reverse order. Once I got it reassembled with a couple of the top mounting screws in, I turned on the breaker and tested for proper operation. Breaker OFF, finish reassembly and remount. You may want to consider replacing foam gasket before remounting. Good luck... R. Moore

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Dual Radiant Burner Element with Limiter

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerAshok from Los Altos Hills CA

Outer element stopped working

Opened the Cooktop. Hardest part was removing the cooktop.
The heating element was broken, very hard to see.

Remove 2 clips and install in new element. Great oppurtunity to clean the unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 3 people found this instruction helpful

Parts Used

  • Dual Radiant Burner Element with Limiter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set

CustomerQiong from Mckinney TX

Outer ring of dual radiant burner doesn't work

Thanks for the previous viewer's tip, disconnect power, pushed the cook top out of the counter and used a wood block for the support. Unscrew the smooth top from the burner, remove old and plug in the new one. Connect power, test OK. Put everything back.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3