Fan Switch Kit - White

PartSelect Number PS2002866

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 3 reviews What's this?
1-3 of 3
 

2 of 3 people found this instruction helpful

Parts Used

  • Fan Switch Kit - White

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerJESSE from VINEYARD HAVEN MA

Switch stop working

FIRST I REMOVED THE TWO SCREWS THAT HOLD THE CHROME PIECE THAT HAD THE SWITCH IN IT.I HAD TO DISCONNECT THE TWO LIGHTS THAT LIGHT UP WHEN THE ELEMENTS GO ON, HAD TO DO THAT TO GET TO THE LOCK WASHERS THAT HOLD THE SWITCH IN PLACE. PUT THE NEW SWITCH IN PLACE BUT COULDNT GET THE NEW LOCK WASHERS ON THE BOTH BROKE, HAD TO GO TO THE HARDWARE STORE AND GET NEW ONES JUST AS LITTLE BIT BIGGER, THEY WENT ON SLICK. THE SWITCH WORKS GREAT AGAIN, BUY NEW LOCK WASHERS BEFORE YOU START

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Fan Switch Kit - White

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerJames from Hillsborough NJ

Switch shorted and burned

Removed grill cover, two phillip screws on front end of the vent holding the switch assembly in place. Lifted the switch assembly and removed the two wires (plugged into lugs). Then removed the two universal nuts with a 3/8" nutdriver and removed the old switch. Cleaned area and put the new switch in place and replaced the universal nuts, then attached the wires. Replaced the switch assembly and the two holding screws. Then inserted the grill cover and Voila! Finished

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Fan Switch Kit - White

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDarrell from Las Vegas NV

Old fan switch was broke.

You probably want to look inside as you read this. Most of it is straightforward, except the retaining clips.

First, I turned off the breaker switch. Opening the control housing, I disconnected the two leads and wrote down their orientation (one is silver, the other copper). In my JennAir model, an orange burner light is on either side of the fan switch. The white plastic on the rear is held on by their keyhole shape - just slide them the only way they can. This gives extra working room.

Since the switch plastic was already decayed, I snapped off the whole central square unit leaving the 2 portions held onto the posts by the metal retaining clips. Using a small flathead screwdriver, I pried up the plastic remnants, working around it until the retaining clips came loose/ broke.

The new unit fit perfectly and easily. The new retaining clips needed to be worked down a small circular file to spread the centers out enough for me to work onto the retaining posts. The file was just barely bigger than the existing hole. The clips can be broken if you are too rough or work them too much. After that, I used a pair of snub nosed pliers to push the clips down the posts. They required a considerable amount of force, but they aren't going anywhere anytime soon.

Reconnect the lights, reconnect the 2 leads, and check for any loose wires from other controls and loose parts. Reseat the control housing, turn on the breaker and test.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3