Ice Maker

PartSelect Number PS1993870

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Ice maker will not make ice.
  • Leaking water.
  • Ice maker won’t dispense ice.
  • Compare At

    $165.14
  • You Save

    $27.52
  • Your Price

    $137.62
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 61 reviews What's this?
1-15 of 61
 

188 of 247 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerMichael from Bradenton FL

Ice maker not working properly and door seal worn

Two screws held the icemaker on. You do not even have to take them all the way out to remove the IM. Replacement of the water valve was just as easy except they (parts manufacturer) updated the flange nut with a compression fitting and it took me a minute looking at it before I realize what was going on. The door seal could not be easier, no tools just a few minutes of time

Help other customers find the most helpful instructions.

Were these instructions helpful?

65 of 81 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerJames from Solon OH

No ice

Removed the plate on the back of the refrigerator, removed the bolt holding the water valve in place (didn't know you could cut the water line to get it off), Plugged in the new water valve and water lines, 15 minutes, very easy to do.
Removing the ice maker was easy, 2 bolts and a plug. Loosen 2 bolts, lift the ice maker off, unplug it. Put the water chute and ice guard on the new one, put it back on the bolts, spend 1/2 hr getting the plug back in (couldn't see past my own hand), Tighten the bolts and you're done.
Really not difficult, except that the plug was angled, and I had to go by feel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

36 of 38 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerGerald from Benicia CA

Ice stalactites were drooling out of the icemaker and gumming up the cubes in the receiving tray.

I first shut off water flow to the fridge. Examination of the package (which was not exact in appearance to the original) demonstrated that the electrical connectors were well-insulated so I arrogantly and successfully proceded without disconnecting the power. My fridge is old enough that the model doesn't appear exactly on anyone's list so I wasn't alarmed that it took an extra 10 minutes or so to noodle out how to adapt the slightly different inlet cowling and electrical cord with extension, but the device is pretty simple.
Soon I loosened the two mounting screws with a nut driver, used a screwdriver to pry away the plastic snap-in housing over the electrical socket on the fridge inner wall and pulled away the electrical plug. The original water fill tube remained in its cavity, ready for re-use.
The new unit's mounting points matched the original screw locations perfectly, as did the fill cowling - which on the replacement icemaker has two possible attachment points. The new unit's electrical connector required an extension pigtail to adapt to my socket, but it was included in the package. The extra cable posed a minor cosmetic issue because it hangs in the collection basket a bit, but that will soon be remedied with a tie wrap.
After the water was restored and an anxious wait of a few hours, we had well-formed ice cubes that weren't all stuck together and the stalactites haven't reappeared.

Help other customers find the most helpful instructions.

Were these instructions helpful?

24 of 29 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerDan from West Bloomfield MI

Ice maker stopped working

I unplugged the electrical connection. Then I removed the 2 screws holding the icemaker in place. I lifted out the old icemaker unit and put the new one in place. Then put the 2 screws back in and plugged in the new unit.

The icemaker started making ice very soon after turning the unit on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 24 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLaura Beth from Mandeville LA

Broken ice maker part

used a screwdriver to remove screw and unplugged part. Plugged in new one and secured with a screw.
Simple

Help other customers find the most helpful instructions.

Were these instructions helpful?

20 of 22 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJoe from Brentwood TN

Quit making ice.

There were not two screws as the instructions said. There was only one screw and I had to firmly pull it out after taking out the one screw. Then, to put the new one in, I had to line up two slots on two knob-like things and push it in firmly. Then screw the one screw in.

Other than the two-screw problem, it was easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 30 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerSteven from Cave Creek AZ

Ice maker leaked water slowly and froze the cubes together

The replacement ice maker that GE supplies for my old refrigerator is a little different than the original. The electrical plug changed from a round plug to a square one. They include an adapter for it, but DON'T USE IT. There's not enough room for the bulky cord and connector. I got a much cleaner installation by taking apart the old and the new ice maker, and then splicing in the old connector into the new ice maker. You need to carefully unscrew a circuit board inside to wire it in, and it'll be more secure if you solider 3 wires instead of using crimp connectors. The instructions also tell you to use your old 'ice breaker', but it won't fit on the new ice maker. I just left the new ice maker's ice breaker on, and it seems to work perfect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 13 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerJeffrey from Bluefield WV

Ice maker quit making ice

the first thing i did was replace the water valve at the bottom of the refrigerator but that didn't work so then i spent more time researching the problem on your site and your diagnostic said to replace the ice maker so i ordered it, took the old one out, plugged the new one in and we had ice the next day.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 8 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCristina from Los Angeles CA

Ice maker not making ice

just unscrewed the 3 screws, attached the rounded plug that came with the unit and screwed back only 2 screws. ice magic in about a couple of hours

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 24 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench set

CustomerGARY from PARRISH FL

Failed icemaker

Shut off power to the refrige. Removed old icemaker, using large hammer. Installed new unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 11 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerJohn from Lodi CA

Ice was melting and freezing in bucket

Frig and freezer were defrosting and refreezing other than normal. Home warranty contractor told me ice maker was faulty. Purchased new ice maker. Unplugged frig, loosened 2 screws with nut driver. unplugged old ice maker, lifted old ice maker out. Took old fill cup off old unit and put on new unit since new fill cup was a different size. Swapped ice maker insert from old to new unit. Plugged in new ice maker, slid over the 2 screws, tightened, and plugged in frig power. New ice maker works fine but still have defrosting and refreezing problem. Figure old ice maker probably works just fine. New contractor still trying to solve problem. Have had problems with this GE Monagram keeping proper temps since it was new in 2005, don't recommend it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerrobert from bensalem PA

Broken ice maker

removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 14 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRobert from Auburn AL

Ice machine wasnt making ice

First I turned the refrigerator and water line off. Then moved to the freezer section, followed the directions, removed the two screws. Directions state to not remove them but I had to in this case. Unplugged the ice maker and removed it from the freezer. I installed the two mounting screws then tried to plug the electrical connection back in but had to use the adaptor cord furnished in the kit. The cord was a little long but I tucked it in and mounted the ice maker. Turned it on then turned the refrigerator and water back on and in a few hours had ice! Very easy to do!

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 15 people found this instruction helpful

Parts Used

  • Ice Maker

Level of DifficultyEasy

Time to do repair:15 - 30 mins

Tools

Customerdebbie from chino hills CA

Icemaker developed a leak and froze over

My husband did the repair, and even though our refrigerator is roughly 20+ years old, he was able to adapt it to work in all the right spots and we now have ice cubes! I'm very happy we did not have to spend $2000 on a comparable refrigerator.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 16 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCharles from Bakersfield CA

Dead ice maker.

Replaced ice maker. Required the removal of one screw and disconecting the control cable.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 61