Rear-Mount Ice Maker Assembly

PartSelect Number PS1992700

This icemaker mounts to the back panel in the freezer section of the side by side refrigerator. This kit includes the icemaker, power cord, bail arm and fill cup.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Ice maker will not make ice.
  • Ice maker won’t dispense ice.
  • Ice maker dispenses too little ice.
  • Leaking water.
  • Compare At

    $108.08
  • You Save

    $18.01
  • Your Price

    $90.07
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 13 reviews What's this?
1-13 of 13
 

43 of 52 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKenneth from Aurora IL

Icemaker made ice but would not release them from the ice mold

Simply swapped out the entire icemaker, works like a charm

Help other customers find the most helpful instructions.

Were these instructions helpful?

23 of 25 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerBrian from Newburgh IN

Icemaker would not eject ice from tray

After three years of cussing this 5-year old fridge for not ejecting the ice, and having to reach in and pull it out by hand, I fixed it with $100 and five minutes. Worse, I probably could have gotten Sears to honor the warranty and replace it when it first started acting up.

Repair could not have been easier. Loosened the two screws/fasteners with 1/4" drive socket set (straight-slot screwdriver wouldn't bite in the shallow slot). Do not remove screws completely; assy lifts up and off the screws for removal. Turn the unit slightly, unclip the electrical connector and remove. Installation is the reverse. Ensure assy sits flush on the screws to assure tray is level.

Although I probably could/should have unplugged the fridge first, I did not. I made sure the ice maker assy was off prior to installation to keep it from cycling on as I attached the ice maker electrical connector, which is before the remounting procedure.

Now it's making so much ice I have to find the plastic shelf cover for the ice bin to keep it from overflowing (which also helps move the ice level bar up to temporarily suspend ice production).

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 18 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMike from Maineville OH

Ice maker quit making ice

This could not have been easier. I came to this website looking to see how much the part was before i called a repairman to come do it. I saw everyones instructions and decided to try it myself. To replace the ice maker you basically unscrew 2 screws, unplug the broken one and remove it. Plug in the new and tighten the screws to hold it in place. I would have been REALLY unhappy if i had called a repairman and saw that was how it was done.
Could not have been easier

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 15 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRichard from Marco Island FL

Ice maker overflowing water

When the ice maker is over filling, either the valve is defective or clogged, or the ice maker is at fault signaling the valve to stay open too long. My problem was the latter. I had already replaced the valve, thinking that being only 2 years old, how could the ice maker be faulty. I was wrong. Ice maker unplugs and comes out with 2 screws. A quick swap with the new ice maker and all is well. Simple

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerJay from St louis MO

Failed icemaker

First I loosened the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...re-installed the new icemaker first attaching the wires and then fitting over the screw holders and tightened the screws. That was it!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRobert from DeFuniak Spgs FL

Ice maker motor shorted out

loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerThomas from Belton TX

Ice maker over flowed

The ice maker would over floew then not cycle it would freeze with the forks stuck in the ice! so just get your modle # and serl, # call in and order the hole ice maker it cost only about $120.00 with shipping!! it is so simple to put in just lossen the 2 1/4 screws in the back and lift up then unplug it. you do not have to turn the water off as it works off the pump at the bottem !!( note you nedd to take the ice bucket out it just slides right out !! You will save the service call from A repair man it is really very easy so by the time it took to read this you will have it done !really its that easy!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerkenneth from lincoln NE

Ice maker quit working & was over flowing

We had to unhook & remove icemaker several times, thaw it out & reinstall, it would work for a day or two then overflow. Bought the new ice marker, replace it and it works great....

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerEric from Greensburg PA

Ice tray wouldent fill.

It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLisa from Fort Worth TX

Icemaker wouldn't keep making ice

Took the old one out, put in the new one, and after a couple of days, had a bucket full of ice. I had been fighting this problem since within the first year of purchase of the refrigerator. It's so great to open the freezer door and see it full of ice!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerMarcus from Bessemer AL

Ice maker non functioning, ice maker not sending signal for w

Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerPhilip from Hemet CA

Icemaker broken

I GOT THE PART, HITCHED IT UP
AND IT STARTED WORKING RIGHT AWAY
IT FIT IN EASILY, AND THE DIRECTIONS WERE EASY TO FOLLOW
THANK YOU

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 11 people found this instruction helpful

Parts Used

  • Rear-Mount Ice Maker Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerALAN from SARATOGA TX

Ice maker shorted out

love this super easy remove two screws and replace thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-13 of 13