Quick Question!

Have you ever purchased from PartSelect.com before?

1990907-1-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz
1990907-1-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz 1990907-2-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz 1990907-3-S-Frigidaire-154637401-Water Inlet Valve - 120V 60Hz http://www.partselect.com/Schematics/Frigidaire/3CKRAE5U.gif

Water Inlet Valve - 120V 60Hz

PartSelect Number PS1990907

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Leaking.
  • Will not fill with water.
  • Not cleaning dishes properly.
  • Not draining.

Compare At

$30.22

You Save

$5.04

Your Price

$25.18
Order within the next 10 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 26 reviews What's this?
16-26 of 26
 

2 of 4 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Elizabeth from canonsburg, PA

The water inlet valve cracked and fell off-again!

FIrst I had to turn off the water supply, remove the bad part and cap off the copper water line.
I found the correct part on line and ordered it. When the part came, I uncapped the water line, doped the ends and refit the valve. Turned the water on an voila!. I actually did it! I was pretty proud of myself. It only cost me the price of the part and not a plumbers fees as well.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench set
Customer: Ronald from Chardon, OH

Dishwasher ran through cycle but no water ever entered the washer.

Turned off water & pulled plug from electrical outlet. Two screws removed the lower cover, two more screws hidden behind the opened door allowed the removal of the bottom panel. Laid a towel under the valve on the lower left to catch water & disconnected the inlet fitting with a 1/2" wrench. Remove the two screws holding water inlet valve next. With valve loose, remove electrical connector and drain hose (pliers). Valve has an elbow fitting that will need to be removed and installed on new valve - use Teflon tape or paste for a leak-free assembly. Reattach the drain hose & electrical connector before installing the valve using the two screws. Once in place, re-attach the inlet fitting (no Teflon required on tapered seats) and make sure everything is tight. Test washer through one cycle for water flow and no leaks. If all is good, remove towel and tools, then re-install the two lower panels. Clean up and you are done!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: Jimmy from Covington, LA

No water in dishwasher

Removed kick plate at lower front of unit. At lower left is water inlet valve. Measured voltage across inlet valve solenoid at start of cycle. Was getting 120V to solenoid, but solenoid not opening valve thus no water going into dishwasher. Ordered replacement inlet valve. To remove inlet valve, disconnect two wires from valve assembly, disconnect water supply tube and remove two screws from mounting bracket. Now you can remove water hose that goes to dishwasher. Reverse order for install of new valve assy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Customer: Michael from Surprise, AZ

Water was not filling the dishwasher at the approbriate time in the cycle.

Pulled the dishwasher out, turned it on the side to gain access to the inlet valve, removed the inlet valve. The hard part was getting the valve fitting that didn't come with the inlet valve. I had to use liqued wrench to loosen the hard water deposits to get it off. Once it was off, putting the new valve on was easy. Also of note, when I tested the old vlalve with an Ohm meeter it read 8 M ohm, not infinity. The new one only measured at about 1k ohm.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: kevin from boring, OR

Loud, not cleaning the dishes, no steam or water.

turned off water supply. replaced the water inlet valve. replaced the updated lower spray arm.
works like new again!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Wrench set
Customer: James from Nashville, TN

Leak on bottom of refrigerator.

removed back cover covering compressor and condenseing fan ,located vavle system,there are two the one leaking was the single solenoid vavle .To remove ,remove screws holding the double solenoid cause the single one is mounted to the double one ,once that done undo the water lines under the double vavle and pull out vavles .The bracket holding the single is connected to the double one by two screws,then undo the water lines ,then the wire connecter,then the reverse of what you do with the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: william from stone mountain, GA

Dishwasher leaking

remove two small screws and slide the dishwasher out, lean it back and see where the water was leaking out. turn of the water remove water supply line and remove the water supply valve. then went to partselect.com and ordered new valve. the dishwasher is now like new for only $21.86 and UPS left the valve at my door in about 4 days::::LIFE IS GOOD

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Derek from Kokomo, IN

Inlet valve froze and burst

*Shut off power to dishwasher at circuit breaker (hot water supply had already been shut off under sink since inlet valve was broken and was allowing water to run into washer nonstop)

*Removed front lower panel from dishwasher

*Removed valve assembly from dishwasher frame

*Disconnected wiring harness from valve

*Disconnected incoming water line from valve

*Disconnected outgoing flexible water line from valve

*Installed new valve in reverse order

It was a pretty easy installation other than the small work area under the dishwasher.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: Steven from Fort Collins, CO

Seal leak from valve solenoid

Turn the water off to the dishwasher. Loosen water supply connector w/ crescent or sized wrench. Remove bracket srews from water inlet. Remove spring clip from discharge hose, remove hose from discharge nipple. Replace with new part in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench set
Customer: Nathaniel from Somers Point, NJ

Washer displayed error message indicating trouble with water.

Shut off water, unpluggewd appliance, removed two screws holding part in place. Removed water supply hose from part to Washer, remover water supply from source to part. Reversed steps with new part. DONE! I'm not handy at all it was mostly luck diagnosing problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 6 people found this instruction helpful

Parts Used:
  • Water Inlet Valve - 120V 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Socket set
Customer: ANDREW from APPLETON, WI

No water during wash cycle, steam only

After checking various forums and advice, the suggested repair was a new water inlet valve. It was easy to change but I wasted $30 as it did not cure the problem. Dishwasher is only 2 years old and is cheaper to replace then have someone come and look at it. So it did not fix the problem, but I recommend Parts Select, the price was fair and part arrived very quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16-26 of 26