1975584-1-S-Whirlpool-Y013783-Inlet Hose Gasket
1975584-1-S-Whirlpool-Y013783-Inlet Hose Gasket 1975584-2-S-Whirlpool-Y013783-Inlet Hose Gasket

Inlet Hose Gasket

PartSelect Number PS1975584

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking water.
  • Compare At

    $3.24
  • You Save

    $.54
  • Your Price

    $2.70
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 4 reviews What's this?
1-4 of 4
 

19 of 28 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerRoger from Lore City OH

(portable ) the hose hook up from the dishwasher to the kitchen faucet would not seal. After replacing the hoses the connection hoses sealede.

tilted the dishwasher back so the bottom was exposed and unhooked the old hoses, then removed old hoses through the back side of the dish washer then fed the new hoses through the back and hooked them up.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 16 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench set

CustomerTimothy from Stafford VA

Water continued to trickle, (sometimes flow), during spin cycle thereby leaving tub with 1/4 to 1/2 filled with water at end of each wash.

Removed washer top by depressing spring loaded clamps with a screw driver. Tricky part was determining location of clamps so that I knew where to insert screw driver; (I used diagrams of my model found on the Internet). With top lifted up, I located water control valve and removed brackets and plastic fixture surrounding it. Was careful to disconnect electronic wiring into valve. Then removed hoses and replaced with new part. Most of the time spent was diagnosing problem, determining plan for getting access to part, and reassembling without losing parts down in tub area. Saved an estimated $150-250 by doing it myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Wrench(Adjustable)

CustomerDaniel from Carlisle PA

Cold water inlet was limiting flow, resulting in slow tank fill time.

When selecting a cold cycle, the inlet valve would allow for slow water flow resulting in 15+ minute tank fill times.

I unplugged the washer, disconnected all water sources.

I removed the 3 screws holding the water inlet value and cover. Disconnected all cabling and water tubing. Replaced valve, reconnected all cabling and reinstalled.

While I was doing the repair on the inlet value. I replaced the hose washer and also installed a screen kit at the home water valve. The home is supported by a well and at times sees sedimentation in the water which could have sparked the initial issue to begin with.

I did clean the old water inlet valve once before which fixed the problem temporarily. It was time to replace the entire part.

This corrected the issue.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerPaul from Pleasant Valley NY

No cold water

I removed the one screw on the plate which exposes the water inlet lines.
Disconnected the two leads to the inlet valve.
Replaced the defective inlet valve and re-connected the leads. Replaced the plate covering
the new inlet valve. Done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4