Quick Question!

Have you ever purchased from PartSelect.com before?

1964673-1-S-Whirlpool-W10181639-Spinner Support and Seal Kit
1964673-1-S-Whirlpool-W10181639-Spinner Support and Seal Kit 1964673-2-S-Whirlpool-W10181639-Spinner Support and Seal Kit 1964673-3-S-Whirlpool-W10181639-Spinner Support and Seal Kit http://www.partselect.com/Schematics/Maytag/59118.gif

Spinner Support and Seal Kit

Compare At

$179.58

You Save

$29.93

Your Price

$149.65
Order within the next 1 hr and 41 mins and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS1964673
Manufacturer Part Number W10181639
Manufactured by Whirlpool

The bolt is built into the support so if the bolt is broken, you need to replace the kit.

This part works with the following brands: Maytag, Crosley, Amana.

This part works with the following products: Washer, Washer Dryer Combo, Dryer.

This part fixes the following symptoms:

  • Noisy.
  • Shakes and moves.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 1.8 / 5.0, 6 reviews What's this?
1-6 of 6
 

96 of 112 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Stephen from Ft Lauderdale, FL

Bearings between spinner and outer tub replaced

The Neptune stacked washer/dryer maintenance manual was a must-have for this repair.

The washer's sound during spin cycle had changed over time from a jet-engine whine to a low rumble. Inspection from the rear revealed that the seals between the spinner and outer tub had failed, and the bearings had been damaged by water intrusion. The bearings are not a replacement item. They are installed as part of the outer tub assembly, so the whole outer tub must be replaced. This requires almost complete disassembly of the washing machine.

The disassembly was relatively easy with the maintenance manual in hand. I had to use a gear puller to remove the pulley, though. I decided to replace not only the outer tub, but the spinner shaft as well since I believed the shaft may have been damaged when the bearings failed.

Reassembly was not so easy. I installed the outer tub, then wrestled with the heavy counterweights. The lower weight was particularly unwieldy, since I had support it from below while attaching it to the bottom of the tub. I finally used books of different thicknesses to hold the weight in place while locating the screw holes for attachment. The upper weight attached easily after I wrestled it into position. This is a concrete weight of about 25 lbs, I would guess.

The other problem was attaching the outer tub cover with the rubber boot attached. It is held by 12 clips, and it was difficult to seat the cover tight enough to attach the clips. I started at the bottom and worked around, instaling clips as I went. The last 4 clips were the hardest; I had to cinch up the cover with C-clamps before installing the clips.

The rest of the assembly was not difficult.

I had my wife help locate the new tub on the struts in the back and to help support the motor while I hung it on the outer tub. Otherwise, this is a one-man repair.

Total cost around $350, thanks to Partselect.com reasonable prices. I shopped around and they offered the best price snd excellent service.

I spent about 8 hours on this job.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

46 of 63 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Paddy from Ferndale, WA

Bearings went out in the drum.

purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..

Help other customers find the most helpful instructions.

Were these instructions helpful?   

42 of 60 people found this instruction helpful

Parts Used:
Level of Difficulty: Very Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Customer: Bradley from Round Rock, TX

Loud knocking during the spin cycle

Removed the Rear and Front Skins of the Washer. Removed the Belt and Tub Drive Wheel from the rear of the Tub. Removed the Front Rubber Gasket and Bracket Assy. Removed the Tub Cover w/Seal, Spinner Balance Ring (both were damaged.) Knocked the Spin Tub forward with a sharp hammer-rap on the Axle (the Axle is pressed into a Bearing that remains in the Stationery Tub.) Removed the Spinner Assy--found one of the securing bolts on the tri-Arm Support sheared off causing an imbalance. Also, the tri-Arm Support was cracked in various places. Replaced all bad parts using the Spinner Support Assy Kit and new Plastic Washers. Replaced everything else in reverse order then tested. Finally, reinstalled all Machine Skins. Very successful, about 3 hours.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

30 of 31 people found this instruction helpful

Parts Used:
  • Spinner Support and Seal Kit
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Fritz from Wasilla, AK

Very loud noise when washing and especially spinning

Pre-ordered the spinner support & seal kit, searched online and found a repair manual, disassembled machine according to the manual, removed snap ring outside of rear bearing, used hammer and drift punch to remove bearings, went to local bearing supply store and purchased 1-6206 2RSJEM and 1-6207 2RSJEM for a total of $43. Used needle scaler to remove the ~1/8th inch of scale from inside of the outer drum and outside of the inner drum and other parts encrusted with scale. Installed new bearings and the seals and new spinner and reassembled the rest of the washer. Now we can't hear it when it spins!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

20 of 21 people found this instruction helpful

Parts Used:
  • Spinner Support and Seal Kit
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Pliers, Screw drivers, Socket set
Customer: Susan from Whiteford, MD

Bad bearings and support arm

We took off the fornt and back of the machine and pulled out the outer tub...then pulled the rear and the front bearings...and the sleeve between...and the support arm...We had only thought we would replace the bearings, but there is a seal in the hub of the support arm that often goes wrong and causes the bearing problem...That appeared to be the case in this fix...so we are glad we chose to replace the arm too. Then we reassembled in reverse order and voila! The machine is as quiet as can be!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

21 of 32 people found this instruction helpful

Parts Used:
  • Spinner Support and Seal Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Customer: Stacie from Las Vegas, NV

The spinner support had sheared off

First, I removed the drum. Removed the spinner support. Removed old seals. Reinstalled new spinner support. Reinstalled pulley and belt. Reinstalled drum. Reinstalled machine covers.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6

Model Cross Reference

This part works with the following models:

PartSelect Number: PS1964673
Manufacturer Part Number: W10181639
Brand Model Number Description
CrosleyCAH4205AWJWasher - Residential
CrosleyCAH4205AWWWasher - Residential
MaytagMAH14PDAALWasher - Commercial
MaytagMAH14PDAAQWasher
MaytagMAH14PDAAWWasher - Commercial
MaytagMAH14PDABLWasher - Commercial
MaytagMAH14PDABWWasher - Commercial
MaytagMAH14PDAEWWasher
MaytagMAH14PDAGWWasher
MaytagMAH14PDBAWWasher
MaytagMAH14PDBEWWasher
MaytagMAH14PDBGWWasher
MaytagMAH14PDCBQWasher
MaytagMAH14PDCBWWasher
MaytagMAH14PDDWWWasher
MaytagMAH14PDSAWWasher
MaytagMAH14PNAEWWasher
MaytagMAH14PNAGWWasher
MaytagMAH14PNAWWWasher
MaytagMAH14PNBAWWasher
MaytagMAH14PNBEWWasher
MaytagMAH14PNBGWWasher
MaytagMAH14PNSAWWasher
MaytagMAH14PRAWWWasher
MaytagMAH14PSAAWWasher - Commercial
MaytagMAH20PDA3WWasher
MaytagMAH20PDAWQWasher
MaytagMAH20PDAWWWasher - Commercial
MaytagMAH20PDCXQWasher
MaytagMAH20PDCXWWasher