1956882-2-S-Whirlpool-W10084141-Electronic Control Board
1956882-2-S-Whirlpool-W10084141-Electronic Control Board 1956882-1-S-Whirlpool-W10084141-Electronic Control Board

Electronic Control Board

PartSelect Number PS1956882

This board is located in the control panel of the dishwasher.Thermal fuse is NOT included.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Will not dispense detergent.
  • Not cleaning dishes properly.
  • Compare At

    $311.71
  • You Save

    $51.95
  • Your Price

    $259.76
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 6 reviews What's this?
1-6 of 6
 

60 of 72 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJessica from Clintwood VA

Lights flashing on the selections and nothing but the cancel button working

Take the 6 torx screws loose and pull down the face. Pop out the bi-metal fuse that is in the current board. Unhook the wires attached. Pop out the old board. Attach the wires to new board. Put the bi-metal fuse back in the board. Re-attach the face on the dishwasher. Be sure to unplug from the outlet before starting. When finished plug dishwasher back in. This fixed my problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?

33 of 59 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customergreg from ozone park NY

Touch pad would not light up

open door remove 8 allen screws

change circuit board 6 wire plugs

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 32 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerTimothy from Arlington WA

Dishwasher would not work

Major appliance retailer sent out a repairman to diagnose the issue with the washer. They determined the control board needed to be replaced. They wanted twice the price for the part plus an additional two hundred dollars to return and install. Total time to remove and replace the part less than fifteen minutes. I purchhas same issue. Once again the repair people, (another $80.00 for the second service call), say the control board muased the part from Part Select and installed myself. Washer st be replaced. I will purchase another dishwasher.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 24 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerRobert from China Grove NC

Dishwasher would not run, only one led on touch panel lit.

Read dianostic sheet included on dishwasher lower panel. It stated to not replace both touch panel and circuit board until you run the dianostic tests. Great fro the manaufactor to save parts money, but the testing would take another hour to perform, so, I was already saving $200 to $300 by doing the repair myself, I replaced both, working slowly and carefully. about 1.5 hours. total cost of both parts was under $300 shipped to me in 2 days. great service for sure. dishwasher onw works correctly. I suspect lightning damage, as we had big thunder stroms earlier that week.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 19 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerHENRY from SALEM OH

All lights were flashing

SHUT OFF CIRCUT BREAKER... REMOVED 6 SCREWS...LIFTED COVER OVER CONTROL BOARD... REMOVED OLD CONTROL BOARD.. INSTALLED NEW BOARD.. REPLACED COVER AND THE 6 SCREWS..TURNED ON CIRCUT BREAKER...TURNED WASHER ON....IT WORKED.THANK YOU FOR THE QUICK DELIVERY!

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 38 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBRAD from GARLAND TX

Would not start - no lights on panel

Pulled the inside door panel off - accessed the control board, replaced it - no improvement - called a service tech to come out.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6