1878632-1-S-Whirlpool-99002138-Rear Bowl Tine
1878632-1-S-Whirlpool-99002138-Rear Bowl Tine 1878632-2-S-Whirlpool-99002138-Rear Bowl Tine http://www.partselect.com/Schematics/Maytag/53706.gif

Rear Bowl Tine

PartSelect Number PS1878632

Sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $26.27
  • You Save

    $4.38
  • Your Price

    $21.89
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Front Bowl Tine with Sleeves

Part Number 2003656

Sold individually.

$23.86
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.9 / 5.0, 16 reviews What's this?
1-5 of 16
 

10 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Robert from Escondido, CA

Rusty racks

Was discouraged seeing rust on both upper and lower racks. Remebered prior dishwasher and $300+ estimate for the racks. But the rusty parts were only some of the small moveable parts of the rack. Each one just snapped out, and the replacement snapped in. No tools at all. Five minutes and $55 later the racks looked new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Donald from Rockford, MI

Front & rear bowl tines were damaged an unusable

removed old damaged tines and snapped new tines into place. Saved myself some cash, received the product in less then 5 days and did not have to drive over to the appliance store in the next town and wait two weeks for them to place the order and at a substantial savings. I'll use your service again when needed.

Donald R. Daily Sr.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers
Customer: Julie from Bedford, TX

Lower dishwasher rack replacement

Purchased a replacement lower rack WPL 99002572 (which had the wheels but not sure that it still does.) Used the old fold down shelf but this might be available as a part. The rack didn't have the tines near the rear of the rack on either side--my old one had fixed/welded tines so I didn't expect this and needed replacement parts to fix it. I Ordered 4 straight clips AP4112831 (99001436)CLIP, FOLD AWAY TINE to hold the tines. There weren't any recommended tines, so found and Ordered 2 each Front place and Rear Bowl tines WPL 12002218 x 2 and WPL 99002138 x 2 that looked about the right length. Used them in pairs. On one side of the rack (right side), only the bowl configuration works--this is because the tines catch on the edge of the basket and won't fold straight up. On the other side (left), I can switch between bowl or straight tines by folding them different ways. To make this work,clip the tines to the basket so the tines set a little closer to the center of the basket than you might expect, in order to allow the tines to 'float' enough to rotate to the opposite configuration. I had to experiment with the clip location so needed a needle nose pliers to gently unlatch the clips so that I didn't break them. I also ordered a clip AP4113042 (99001746)Latch, pivoting tines--but didn't use them with these bowl tines. They might be useful with a straight tine for latching the top to the outside of the basket.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Gary from Niles, MI

Rear bowl tine broke, rusted through in one spot.

Ordered BOTH the front and rear tines as the front tine showed some superficial rust through the plastic covering in a couple of spots. Re-used the tine holders which were still solid condition and flexible. Snapped bowl holder tine unit out of dishwasher, snapped new tines in place, snapped unit back in dishwasher. Took 5 minutes or less. All other parts of the dishwasher rack were still in excellent condition with no cracked spots on the vinyl covering or rusted spots visible anwhere.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: John from Mission Viejo, CA

Old parts had worn out

Replaced and repaired in less than five minutes using No tools

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 16