Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS1847969
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
This is a package of 2 filters.
Slide grease filter about 1/2 inch to right (or left) using the d-ring attached to one side and then pull down and out. Push charcoal filter frame slightly to rear and pry down from front. Install new charcoal and grease filters by reversing process. No tools - 5-minutes max!!
Help other customers find the most helpful instructions.
Were these instructions helpful?
I took the old one out and put the new one in. I want to take this time to tell you that I have repaired a few of my appliances with very little difficulty and a much lower price than Kitchen Aid charges. One was a Micrwave vent, knobs on a stove top, little rubber knobs on the bottom of a grate of my cook top which was triple the cost from what I paid to Parts Select and the water seal on a dishwasher. Thing wear out and need to replaced; however most of these things can be repaired by the consumer.
Our Microwave Vent Grill was broken - and since I was ordering online, I figured I'd get the two filters as well. The Vent Grill was fairly easy to install. It was a little tricky getting it to fit in, but once in, it was just a matter of screwing in at the top.The Filters were another matter. The FILTR-GRSE came out very easy, but what I didn't realize was when I ordered it, it only came in packs of 1. The Charcoal Air Filter came in packs of 2, so I assumed both did. Why, when you need two of each of these, do they sell one in single packages - and the other in packs of two? The Charcoal Air Filters were only replaceable by unscrewing the bottom of the microwave. The FILTR-GRSE were easy enough to just pop out. Overall, not that bad of an install.
I went online and found the manual for this appliance and used the instructions, which were very helpful. The filters just pop out and the new ones fit right in. No tools were needed. For the vent grill, it was necessary to move the metal tabs back and forth a few times manually before they were properly placed in order to take the two screws, which hold the grill in place. I then loosely tightened the screws (so as not to crack the plastic grill)with a Phillips Head screwdriver. When my husband got up from his nap he was pleased to see the job completed without his help.:)
The trick is to align the bottom and top tabs first. This take a little coaxing and patience, but once these snap in, the tabs with the threads line up perfectly.TIP: Thread the screws into the metal tabs while supporting the tabs with your hand BEFORE installing the grille, back them out, and then install. The threads were a little tight, and putting a lot of pressure on them while the tabs are in the slots risks breaking them off.
Removed old grease screens by sliding sideways and then pulling out of the grooves. (helps to have rubber gloves as the grease is slippery). Put pressure on the back of the charcoal filter rim and allow side closest to you to drop down slightly so you can get a fine flatblade screwdriver under and pop the filter out of the holder. Works same on both sides. Install new charcoal filters after cleaning the holder edges with soap and water and drying. Make sure charcoal filter is in the second set of holder grooves and snap in place. Replace new grease filters with the pull tabs down and facing the center. Slide the grease filter into the holder grooves a little further back than normal and (using the pull tabs) pull the filter back the other way until flush with the opening and in place. The top exit ports are removed by taking out 4 screws;however, two of them are attached to spring clips on the underside and it is easy to break off the tiny plastic ridges underneath. The other screws come out easily and the entire exit port piece can be removed and cleaned. To reinstall just snap exit port back in place and replace screws. If you have broken off the slender plastic ridges you can sometimes turn the screww a partial turn and engage what is left; if not you may have to put some rubber grommets or pieces to support the bottom and keep pressure on the exit port piece which is not locked by only two screws.
The repair was simple and easy. It required a Phillips head screw driver only. I Removed the vent grill and replaced it with the new grill there were only two screws that needed to be removed then refastened. Total five minutes. I also replaced the grease filters which took about a minute total time. I do many of my own repairs to my home and appliances .I've found your service parts delivery prompt and precise.
Why a tenant would remove and discard the grease filters without replacing them is beyond me! But, I removed the filters from the package and slid them into place. Two minutes tops. I would like to add that I ordered these on Thursday afternoon, and I had them on Saturday; awesome customer service!
It was a simple replacement of grease filter and charcoal filter in microwave/hood combination. I did use a screw driver to pry out the filters, but otherwise no tools. It was easy and straightforward.
both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.
Replaced grill and greese and charcoal filters.
Used hands to slide filters sideways, till they could be pried out with screwdriver or bare hands. When new parts arrived, easily slide new filters into position. In hindsight, we did not need to replace grease filter. I was able to clean one of those with ordinary dish soap, warm water, and a brush.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.