Front Glide Kit

PartSelect Number PS1804752

This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. Also, a rivet tool is required for this kit - purchase locally.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Marks left on clothes.
  • Will not tumble.
  • Will Not Start.
  • Compare At

    $13.09
  • You Save

    $2.18
  • Your Price

    $10.91
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 55 reviews What's this?
1-5 of 55
 

422 of 520 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerJohn from Charlottesville, VA

Belt broke on old machine.

1. Removed front of machine (2 screws at the bottom).
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.

I also cleaned the lint from the cabinet and from the vent hose.

In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.

I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

287 of 366 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerMark from Lafayette, LA

Dryer squeeking loudly becoming worse quickly

I received my parts promptly and had no problems, they were accurate and fit well.

After removing the screws to the front door and panel I removed the wires to the door switch. Carefully I removed the belt and removed the drum. I took the time to vacuum all of the lent from the inside and and remove from all the wiring, motor and heating elements, etc. I replaced the drum rollers, belt, front glides and a buzzer that was on the blink. I reassembled the dryer and unforetunately the dryer was still squeeking. I later repeated the process and found that the tensioner wheel for the belt was the culprit. I cleaned then greased the bearing portion and replaced it. I reassembled the dryer a second time and now it's quiet as a mouse. By the way, you will need a rivet gun to replace the front glides and I recommend you give the belt tensioner wheel a good inspection the first time.

If your dryer is squeeking, go ahead and order the tensioner wheel also, it's a little money spent toward making sure you get rid of the noise! It might save you a lot of time and trouble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

149 of 220 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Wrench set

CustomerFrederick W. from Austin, TX

Motor buzzed and dryer drum would not spin when pressing start

From the first time the motor buzzed (but dryer tumbler then started to turn), 2 weeks elapsed for the dryer drum to stop turning altogether. If this occurs, DO NOT continue to push the start button because the motor armature wiring will heat up and the insulation will begin to melt and smell - a SAFETY HAZARD. Unplug dryer and lockout/tagout as appropriate.

Through basic troubleshooting, discovered the motor had seized up. Since the unit was about 10 years old and it had to be disassembled for replacement, the decision was made to replace "likely to fail mechanical components including motor, belt, both rear drum rollers/shafts, idler arm pulley/assembly/wheel, associated washers, snap rings and both front glides. Reviewed the PartSelect website and drawings, ordered the parts and they delivered on time. Buy the correct sized snap rings at a local hardware, they're much less expensive. Also once inside your dryer, you'll likely find alot of lint to vacuum out...have fun.

I went online and Googled several resources that showed how to remove the front dryer panels, as well as PartSelect repair stories. From that point on, I took photos as I was disassembling so I would know how to put it back together. Utilize pictures or whatever system you prefer to keep track of taking something apart and putting it back together.

Remove the dryer door, then the front panel Disconnect wires to the light, dryness sensor and door switch. Note belt and pulley configuration that is near the motor-this will help you later when reinstalling the belt. Also note if the ribbed side or the flat side of the belt is against the outer drum wall. Remove the door shroud.

Slip the belt off the idler pulley wheel. Remove front drum support, then dryer drum Note which end of the dryer drum is the front and the orientation of the glides on the drum support. Discard old belt. Drill out and remove the old front glide supports, then install/rivet the new glides.

Remove both old rear drum rollers/shafts, washers, etc. The rear drum roller shafts are secured to a back bracket by a hex nut....feel around you'll figure it out. Replace new roller shafts. Lightly grease using a high quality silicon grease, then replace new washers, roller, snap ring, etc

Carefully unplug wiring harness on motor, there are fragile clips on each end. Don't forget a separate ground wire from the harness is attached to the motor mount bracket. Carefully release tension on the idler arm spring. Using the correct size nut driver, remove three screws (on this model) then take out the motor/idler arm assembly. Remove the old idler arm/pulley assembly. Remove the motor mount clips on each end of the mount (I used a wide blade screwdriver). Remove and replace the motor. Motor configurations changed after Whirlpool bought Maytag, so orient it correctly insuring mounting gasket "nubs" on each end of the motor correspond to the cutouts on the motor mount. Reinstall the motor mount clips. Replace the new idler arm assembly/pulley wheel; grease moving parts with high quality wheel bearing grease. Replace motor/mount bracket assembly back into the dryer. Replace ground wire to motor mount bracket and plug wiring harness back in. Reinstall idler arm spring.

Place belt back on the dryer drum and move into place on rear rollers. Reinstall front drum support. Dryer drum should turn relatively easy. Insure belt is oriented on the drum correctly before connecting belt to motor shaft end and idler arm wheel pulley (the picture you took comes in handy here).

Reinstall the rest of the parts in reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

66 of 129 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerJoseph from Demotte, IN

Noise, possible low exhaust flow

1 Disconnect dryer from electrical outlet
2 remove vent pipe
3 Tilt dryer backwards and remove front cover bottom 2 philips screws.
4 remove lint assembly and then the fan blower housing with nut driver.
5 with pliers remove retainer clip from fan
6 remove snap ring with pliers or a flat blade screw driver will also work.
7 remove fan
at the same time I replaced the front glides if you do not want to do this then reinstall in reverse order and job is complete.

for glide replacement
1 remove the 4 screws holding the outer ring to the frame of the dryer.
2 drill out old rivits from the back side and then knock out. be careful to only drill rivit and not into metal frame
3 install new new glides makesure you install in correct direction.
4 install pop rivets with stud end on top side of glide. pushing rivet through glide and into the frame ring.
5 pop rivits and make sure they are secure.
6 reinstall ring making sure seal is around ring correctly
7 reintal 4 screws.
8 follow reassembly of blower and lint housing if you changed the fan. if not then just the lint assembly.

good luck the job is really easy and you will save yourself some money

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 28 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerJim from Los Angeles, CA

Drum rubbing metal to metal on front support

1. Unplugged dryer, removed front (2 phillips screws near bottom) set aside with wires attached
2. Removed front support (4 hex head screws)
3. Drilled out pop-rivets, discarded old glides (why didn't Maytag use rollers?)
4. Riveted new glides in place.
5. (Oops!) trimmed cork pads, smeared with glue, shoved under glides, held down until firm
6. Removed drum (pushed belt back to groove, pulled drum off rollers, lifted belt off drum, worked drum out) Left belt on pulley and tension wheel as pattern when I replace it.
7. Scraped old gasket felt off back chassis and front support
8a. Folded gasket lengthwise and glued into front support channel with fold on outside diameter. It was too short.
8b. (Oops! Why didn't this come with instructions?) Pulled it out, reversed it and replaced it with fold to inside diameter. It fit. Glued ends together.
9. Glued other felt gasket into back chassis. (Good ventilation needed here!)
10. Replaced rollers. (This did have instructions, despite being easy. I didn't use any grease. Experience as a locksmith says don't lube anything that isn't sealed from dust. I also vacuumed out 15 years of dust.)
11. Replaced belt. (The old one looked fine, but I was advised to do the belt and rollers along with the glides.) The grooves touch the drive pulley, the flat goes around the tensioner, and the belt exiting to the left seems like it will rub the pulley, but it doesn't once the drum is installed.
12. Turn the drum around (Nice, it's symmetrical!) and work it back in.
13. Lift the belt around the drum edge (I used bull clips to hold it in place.)
14. Check the belt on the pulleys, move the drum in more, take off clips, move the belt to the groove.
15. put the drum on the rollers, lift the belt out of the groove, and spin the drum a little while watching the pulleys to check it.
16. Screw the front support back in place.
17. Screwed the front on and plugged it in.
It works!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 55