1777057-1-M-Whirlpool-12002535-Wax Motor
( Grid squares measure 1x1 inch )
1777057-1-S-Whirlpool-12002535-Wax Motor 1777057-2-S-Whirlpool-12002535-Wax Motor 1777057-3-S-Whirlpool-12002535-Wax Motor
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Wax Motor 12002535

Rated by 4 customers 

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 24.72
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS1777057
Manufacturer Part Number 12002535
Manufactured by Whirlpool
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# 12002535 replaces these:
AP4009198, 1063620, 12002535
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.3 / 5.0, 4 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No Door Light and not spin drying
opened door remove door with two screws at hinge. Remove two screw opposite door hinge. Pull front cover sides near the area of the top screws you just removed. Cover will pop loose and tilt forward remove from bottom clips. Remove two screws at the top in the front of machine that is behind the front cover that was just removed. Remove four screw in soap fill door. Lift top of machine this will expose the wax motor near door latch. Remove metal clip holding wax motor in place. move motor to left and push left side of wax motor this pop the right side out of clip. You can remove two wires from wax motor. Install wax motor. Reverse order to put machine back to together.
Read less
  • Michael from Orland Park, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer stopped during rinse cycle.
First I removed the front door. Then I removed the front of the washer. The wax motor is in the center at the top. Remove the clip that holds it in place. Slide the motor to the left and remove.
However, this was not the problem. The true problem was a plugged inlet screen where the cold water hose is connected. This makes for a long fill time during the rinse cycle, and the machine stops. Clean both of the inlet screens (cold & hot) and the machine works perfectly!
Read less
  • Curtis from Elizabethtown, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer Would Not Spin Or Empty.
Followed the instructions I found inside the control panel after a repair man showed me where it was. He suggested I call and get the parts since his company said they were back ordered for 10 days. So I saved $250. 00.
Other Parts Used:
Wax Motor Control Board
  • Walter from Auburn, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
18 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not lock
I removed the cover above the washer and below the dryer (stackable washer and dryer). Removed the spring behind the wax motor and unhooked the wires. Then I pulled out the old wax motor and put the new one in.
  • dana from north pole, AK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
You May Also Need ?
Door Lock/Spin Enable Switch
$41.40
$41.40
  In Stock
Control Board
$232.32
$232.32
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1777057
Manufacturer Part Number: 12002535
Brand
Model Number
Description
Maytag
MAH14PSAGW
Washer - Maytag Washing Machine Model MAH14PSAGW Parts
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Wax Motor
$ 24.72
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.