Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS1766009
This drive belt is 89.5" long.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
We live in a Condominium, space is tight especially in the Utility room where the washer/dryer are located. Turned dryer breaker off at the electical panel. Removed the top cover and front assembly w/door and front drum support, right where the unit was located. Had to gain rear access to loosen drum drive belt so undid the dryer vent hose to floor connection through a front acess hole. Moved the unit out to the breakfast nook as well as disconnecting the power cable from the wall socket. Removed the rear access panel covers and unhooked the drive belt. At the front removed the top screws off the lower cross member to allow spreading of the side covers to allow the removal of the drum. Removed drum and found the bearing bushing gone, reduced to powder.Using the supplied instuction sheet, replaced the rear bearing assembly, replaced the drum after vacumming the whole interior and started the reassembly of the unit using the new belt and moved the unit back into place. Reconnected the power cable and dryer vent then lastly replaced the lint filter and selector knob. Closed the breaker and turned on the machine, no noise!!!Incidently I am 78 years old. Thanks PartSelect.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.This was a first attempt ever at fixing an appliance and it was no big deal.
The repair was done as follows:1. Removed the door2. Removed the two screws securing the top panel then removed the panel.3. Removed the two screws securing the front panel then removed the panel.4. Removed the screws securing the left side panel then removed side panel and the two leveling feet.5. Tipped dryer over on its back (you will want to protect your floor, the four screws that attach the heater unit protrude through the back).6. Disengaged the belt tensioner and removed the belt and the drum.7. Removed the three Torx screws securing the drum bearing to the drum and discarded old bearing.8. Removed the four screws securing the bearing retainer to the heater unit.9. Removed the four screws securing the heater unit and two sensor wires.10. Lifted heater unit just high enough to remove bearing retainer. Discarded bearing retainer.The new drum bearing kit is supplied with self tapping screws. I installed the screws into the bearing parts to tap the holes and then removed them prior to assembly.11. Installed new bearing retainer to back of heater unit using the supplied screws. Install the four screws by hand, finger tight.12. Re-attached heater unit and tighten screws.13. Re-attached sensor wires.14. Tightened the four bearing retainer screws.15. Attached new drum bearing to drum using the three supplied Torx screws. I used tape to hold everything together while installing the screws. Tightened the Torxscrews.Next I used a vacuum to remove all the lint from inside the dryer. I also used a small plastic putty knife to remove the caked on lint on the impeller blades.16. Inserted drum bearing into bearing retainer.17. Installed drum belt and belt tensioner.18. Installed left side panel and feet.19. Replaced the two grey and two white slide bearings on the front panel. They just slip onto a small post and slide into a slot.20. Installed front panel. (Rotate drum to help with installation)21. Installed top panel and door PROBLEM SOLVED!
Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a snap.
Removed the top of dryer two screws behind door at top then removed top two screws top corner lift dryer tub put belt around the tub then looped belt around the pullies.
I had to take most of the dryer apart because there is no rear access to the motor. It turned out to be easy to dissasembel the dryer. The only problem that I had was that I could not figure out how to route the belt around the motor and the idol pullies. I could not find anywhere that gave instructions on how to properly tension the belt. I finally figured out that the idoler pulley needs to be locked in place on the right side of the engie mount. Then the belt needs to be routed over idoler pulley and under the motor pulley. Finally release the idoler pully from the locked postion to put tension on the belt. It really turned out to be pretty easy.
Replaced idler pulley and belt very simple
I removed the two screws that hold the front panel to the top panel. I removed two more screws that hold the front panel to the side panels. I separated the front panel from the side panels and removed the drum. I could see on the front panel the drum slides were badly worn. One was gone. The new parts installed easily using no tools at all. Everything snaps in place. The new foam gaskets press and stick to seal the duct work. The felt strip pressed into place. I replace all the panels in reverse order and plug it in. It operates fine, but the motor is making the noise. I will look into replacing the motor next.
I've always heard it was a simple job to replace the belt and that would solve the problem. I'd defer to others online when they suggest to replace the rear bearing - they are totally right about that suggestion. My bearing basically fell apart in my hands. Not sure if I needed a belt or not, but it's worth replacing while you are tearing the thing apart. It took way longer to tear apart than to put back together. The parts and prices from PartsSelect were perfect. The parts were received in 4 business days as they said and were perfect replacement parts.
1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.
The diagrams on the Parts Select web site is what made it easy for me. I could see from the diagram how the dryer was assembled. I removed the two screws holding the top on then separated the front apart from the drum. I did have to remove the panel in the back where the power connects to access the drive pulley and belt tensioner. I slid the old belt off and simply reversed the procedure for the new one. Put it back together and it runs beautifully. I also installed a new door gasket with no tools. Now it does not leak lint from the fronf door.
took two screws off the front. They were behind the door. These screws held the top on. Lifted top off and took two screws from the frame holding the front door and panel on. Disconnected three wires and removed front panel. Laid dryer over on right side and removed four screws from bottom and back,two from control panel and removed left side.lifted drum out and removed belt. Removed nut cap and idler pulley wheel. Replaced same. removed three screws holding screen and rear drum bearing to drum. Replaced same. Removed electric heat coils from back and removed receiver for rear drum bearing. Replaced same. Put everything back in reverse order. Works better than new!!
After finding the belt was broken, I also discovered the idler pulley was broke. Your website made it incredibly easy to identify and purchase the parts. This is my third great experience with your site. The last repair was the whole front bearing assembly and that went very smooth thanks to your site. Keep up the great work and thanks again.
Started off not knowing what I was doing at all, never worked on a dryer before. I knew the drive belt was broken so I had to get to the inside of the machine. I started taking screws off (way more than I needed two) then I finally discovered that I only needed to remove the two screw in front of the dryer that secure the front panel to the top panel. I took the two screws out and the top lifted right off and the front panel/door assembly came off giving me access to the drum. I was then able to easily remove the drum which gave me easy access to the heater assembly. I removed the heater assembly and found one of the coils had broken. At the same time I realized that I purchased the wrong heater coil kit but I was able to still use the supplied coil with a little ingenuity. I then reinstalled the heater assembly into the dryer.The drive belt drove me to drink a few beers later that night. I thought it would be a breeze to install but nooooo! After reinstalling the drum and trying to reach my hands into places not meant for hands to go into, and loosing some blood in the process, I decided it might be smarter to remove the side cover. Well that was a much better idea. I was able easily rout the belt over the drive pulley and tensioner.All the covers went back on with ease and the dryer works like a charm!Overall not a hard job. I guess I just made it hard because it was my first time ever working on a dryer.Now if I can ever figure out where those two extra screws came from......?Scott D.
First remove top cabinet panel by removing two small screws under door recess; then swing up lid and remove from hinged area at the rear. Once top panel is removed, remove the front panel and door assembly by removing two attach screws securing front panel to dryer cabinet. Swing the front panel down and remove from two base hinge points. Slightly lift the front of the dryer drum and wedge some rolled up newspaper between drum and frame to provide access to get your hands through to the idler pulley and motor area. Remove the belt form the motor & idler pulley; then slide the drum out of the cabinet to gain access to the idler pulley. Remove nut securing idler pulley from bracket and remove and replace with new part. Reverse the process to complete the installation.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.