This is a red indicator light lens for an oven that covers the indicator light for the surface element. The indicator light signifies when the element is on and heated. This part is sold individually. It is recommended to check other red indicator lights in case they need to be replaced because they often wear at the same rate. It is difficult to see the light without the red lens. This part does not include the light. If your light does not illuminate, you may want to consider ordering the light as well. Tools required for this repair are a 1/4 inch nut driver and a stubby Phillips screwdriver.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Jack S - June 29, 2019
Verified Purchase
worked perfectly
The Indicator Light Lens broke off and fell out. I ordered two and replaced the broken one and the other one as well. They fit perfectly. Our stove is several years old and I wasn't sure if I could find a replacement. So glad PartSelect had the replacement. If I need another part, I will order from PartSelect.
★★★★★
★★★★★
Mark M - June 24, 2019
Verified Purchase
Necessary But Way Overpriced
This little bit of plastic is almost $7. Unbelievable! Unfortunately it is necessary if you want the indicators for your burners to work. Not a bad markup, though, for a part that likely costs 50 cents to make.
★★★★★
★★★★★
Edward M - March 8, 2019
Verified Purchase
Exact parts I needed lens and light)
Lens had broken on one of the controls on my stove, and upon inspection, discovered that the 'legs' on the light had broken off (which grip the lens) as well. Found the parts I needed on PartSelect, ordered, received very quickly, and only took me 15 minutes to disassemble the stove and replace with the new parts! Saved an expensive trip to the house by an appliance repair person!
★★★★★
★★★★★
Ivan S - September 12, 2018
Verified Purchase
Easy Repair - Perfect Part
All pieces came together. Unfortunately since this is a small part I had to call to double check if it shipped. Customer Service was friendly and helpful. Great Job!
★★★★★
★★★★★
David K - February 13, 2018
Verified Purchase
Fits and Works
Rather expensive for a tiny chip of plastic, but it fixed my stove.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.8 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Lenses wore down and broke off making the actual indicator lights fall down behind the control panel since the lights connect to the lens.
Pulled stove out and unplugged it. Used a Phillips screwdriver to take the back cover off of the control panel. Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control p
... Read moreanel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others. Replace back cover. Plug stove back in and slide back into place. There are you tube videos out there to help you.
Read less
Charles from OMAHA, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lens was broken
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Kenneth from Coeur d'Alene, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lens missing for burner "on" indication
Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens
Carol from Houma, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
21 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.