1735034-3-S-Whirlpool-W10116789-Folding Tines Sleeve
1735034-3-S-Whirlpool-W10116789-Folding Tines Sleeve 1735034-1-S-Whirlpool-W10116789-Folding Tines Sleeve 1735034-2-S-Whirlpool-W10116789-Folding Tines Sleeve http://www.partselect.com/Schematics/Maytag/36254.gif

Folding Tines Sleeve

PartSelect Number PS1735034

Sold Individually. White in color.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $5.68
  • You Save

    $.95
  • Your Price

    $4.73
Special Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 10 reviews What's this?
1-5 of 10
 

186 of 256 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools:
Customer: Gregg from Woodbury, MN

Dishwasher leaking (small puddle)

My dishwasher was leaking a small amount and it seemed to be happening during the last half of the cycle. The insulation at the bottom of the door was wet but not directly under the dishwasher by the motor etc. I tried the door gasket which was a simple 2 minute job but that didn't solve the issue. I took apart the door by removing the seven torx head screws on the inside (don't worry about the metal pieces on the sides with the phillips screws). I could see some white powdery build up and watermarks coming from the soap dispenser area. I thought maybe there was crack in the door. But after taking out the solonoid (it just snaps in and out) I could see light around the little latch that holds the soap dispenser door shut. I tried a bit of caulking but it just fell out after a day or so. Then I found the little grommet on PartsSelect.com. You have to take off a white plastic cover that covers the door latch mechanism - it snaps in and out on one point. A couple screws hold the plastic assembly in place. You can just remove the whole assembly, it doesn't need to be taken apart. Remove the old grey gasket around the latch and put the new one over the latch. It's more like a "boot" like around a shift lever in a car. Put the assembly back in with the latch going through the hole. Make sure the gasket covers the hole. Tighten the screws down, not so much as to tear the gasket but enough to be snug against it. Snap the white cover back on. Snap the solonoid back in place. Put the door back in place. Put the seven screws back in. You're all set - no leaks. The key to troubleshooting was that it started leaking during the rinse cycle after the soap dispenser latch had flipped up exposing the worn boot around the latch.

Help other customers find the most helpful instructions.

Were these instructions helpful?

130 of 254 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Gina from West Alexandria, OH

Wheel had broken off along with the folding tines' clip

All I had to do was to snap the parts into place. I also had someone come here to find a leak in my dishwasher. It was in the latch and seal that kept the soap dispenser closed. They wanted to charge me over $50 when the part only cost less than $9 with shipping. I just ordered it and installed it myself. Piece of cake!

Help other customers find the most helpful instructions.

Were these instructions helpful?

67 of 131 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Manfred from Fredricksburg, VA

Some of the fold up/down tines in the lower basket were defective as well as the door handle was broken

The wheels and clip were just snapped in to replace old or missing ones. The door latch required the inside cover of the door assembly to be loosen enough to remove the old latch and replace the new latch.
approximately ten screws were involved.

Help other customers find the most helpful instructions.

Were these instructions helpful?

65 of 127 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Greg from Towanda, PA

Clips holding folding tines broken

The clips holding the folding tines on the lower rack had broken, so the folding racks were flopping around. I entered the model number an PartSelect popped up exactly the right diagrams to find the parts I needed - I even found the handle for the silverware tray that I didn't know was missing. I ordered before noon, and the parts arrived the next day, all at a very reasonable cost (even shipping!) the parts just snapped in place. I'm very, very pleased.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Robert from Escondido, CA

Rusty racks

Was discouraged seeing rust on both upper and lower racks. Remebered prior dishwasher and $300+ estimate for the racks. But the rusty parts were only some of the small moveable parts of the rack. Each one just snapped out, and the replacement snapped in. No tools at all. Five minutes and $55 later the racks looked new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 10