| |
15 of 17 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsSocket set
CustomerDaniel from Millmont PA
Dryer wouldn't heat
This was the first time I ever attempted such a repair on an appliance, but it was fairly easy once I figured out how to take the front of the dryer off! I was almost certain that the igniter was the problem was it didn't glow like it did before. On this particular LP Gas dryer from Maytag there is a little service door on the front near the floor. It is almost impossible to get your arm in there plus still have room to shine light in! I took off the two screws at an angle down near the floor and the whole front came off. I used a mini socket wrench to disconnect the igniter. I didn't have to remove the screw as the part slips on over the screw, then you just tighten the screw, connect the cable and it worked perfectly! Thanks PartSelect! As for the lint filter...the original has been broken for probably close to 10 years. It was just a matter of slipping the new one in.
|
8 of 8 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRichard from Valley Center CA
Broken lint filter screen frame
This is hardly a "repair". You toss out the old lint screen and put the new one in. The hardest part was getting the lint screen out of the plastic bag it came in...
ta da it is done...
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDeborah from North Attleboro MA
Dryer lint filter had rips and holes
Researched for part on PartSelect, ordered part, arrived next day, cut open delivery package and plastic bag containing lint filter and placed new filter in dryer filter channel. Quick & super easy - my kind of DIY!
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerwilliam from salt lake city UT
Lint filter was old and had hole in it
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerBrad from Georgetown TX
Old lint filter had damaged screen
Took out the old lint filter and put in the new one. Works great
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerM. Lyn from Arkansas City KS
Lint filter screen torn
Inserted new lint filter...one second! No tools needed. Price excellent!
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerAlan from Pacific Palisades CA
Lint filter was frayed
used a utility knife to open the box in which the part was shipped, discarded the old filter and inserted the new one
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:More than 2 hours
ToolsScrew drivers, Wrench set, Wrench(Adjustable)
CustomerMichael from Westlake OH
Drum dragging and squeaking loudly.
Disconnected the dryer, removed the front cover, front drum support, and the entire drum (30 min.). Completely cleaned all lint and debris from inside the dryer (30 min.). Installed the new tumbler roller shafts and drum support rollers (20 min.). Installed the new drive belt (30 min.). Re-assembled and re-connected the dryer and ran to verify operation (30 min.). The dryer runs like new.
I found I didn't need the front glide kit , as I replaced the glides a couple years ago and they were in excellent condition.
All in all, the parts, service and instructions were outstanding. I will use PartSelect whenever I need to repair my appliances from now on.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsPliers
Customerbill from brighton MI
Lid hinge was broken, lint screen had a hole in it.
Remove part from package. put in place. press in pins. done. Now I'm ready to fix the tub bearings and the wax motor ! save $500 or more.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerKENNETH R from NORTH ARLINGTON NJ
Lint filter with hole in mesh
Replaced with new part from PartSelect . Works Fine.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerPatricia from North Bend WA
The screen in the old, original filter had a hole in it...
Took the old filter out, put the new filter in...bingo! Repaired
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers
CustomerJohn from east liverpool OH
Rattling noise
replaced tne blower wheel using instructions from Parts Select web site.Received the parts second day after I ordered them from Parts Select. Very pleased with results. Thanks for the help.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJacqueline from South San Francisco CA
Lint filter starting to develop holes
Checked on-line for part and ordered it. Replaced filter with new one.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRobert from Sacramento CA
I relaced our worn out lint filter
My part was not amazing. What was genuinely cool: I ordered it one day and it was here the next, took out the old and put in the new. Thanks for getting it here so quickly.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerRuth from Alexandria MN
Broken lint filter
I just pulled out the old one and put in the new one! Thanks for making it easy for me to order my part online!
|