1595603-1-M-Whirlpool-304997-Automatic-Dry-Sensor-with-Mounting-Screws.jpg
1595603-1-S-Whirlpool-304997-Automatic-Dry-Sensor-with-Mounting-Screws.jpg 1595603-2-S-Whirlpool-304997-Automatic-Dry-Sensor-with-Mounting-Screws.jpg 1595603-3-S-Whirlpool-304997-Automatic-Dry-Sensor-with-Mounting-Screws.jpg

Automatic Dry Sensor with Mounting Screws

PartSelect Number PS1595603

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Shuts off too soon on auto dry.
  • Will not shut off.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Compare At

    $28.97
  • You Save

    $4.83
  • Your Price

    $24.14
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 3 reviews What's this?
1-3 of 3
 

18 of 26 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerGeorge from Smithfield KY

Clothes would not dry on automatic setting

1: (Automatic Dry Sensor) Removed 2 screws holding front panel, then removed 2 screws holding automatic dry sensor to inside of tub. Disconnected 2 wires from under side of sensor and removed sensor. Placed new sensor in place, reconnected wires, and reinstalled 2 screws. Finally, put cover in position and secured with 2 screws.

2: (Pilot Lamp) Removed 2 screws at bottom of washer front panel. Pulled bottom of front panel forward and removed from unit. Pulled lamp socket from clip, replaced bulb, and replaced lamp socket in clip. Reattached front cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 12 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerW. Dale from Newton KS

Dryer did not turn off in auto-dry mode

Unplugged the dryer (electric), removed two screws at bottom of front panel and removed front panel. Pulled electrical clips from sensor lugs near center.front of drum exterior. Located sensor inside front of drum interior, removed screw at each end. Removed old sensor, placed new sensor in position, attached with screws. Installed electrical clips on lugs, closed front panel and secured with two screws. Plugged in the dryer and it worked!

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 707 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Wrench set

CustomerNat from Baton Rouge LA

Dryer tub rollers making loud noise. Dryer would not dry on automatic cycle.

Disconnected dryer, took off front, took off screen housing, took belt off pulley and lifted out tub. Removed snap rings from roller shaft and removed rollers. Then removed roller shafts. Reversed procedure and added new shafts, rollers, washers, nuts and snap rings. Put tub in and put belt on pulley. Replaced auto dry sensor before replacing lint screen housing and connected wiring. Put front on and connented dryer. Be very careful when working with roller shafts. My wrench slipped and I ended up with 8 stitches in my right hand. The sheetmetal is sharp!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3